Bedienungsanleitung Hoover MaxExtract Deep Cleaner (Seite 11 von 60) (Englisch, Französisch, Spanisch)

594429

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Actual model may vary from images shown.

PICKING UP SPILLS

Your HOOVER

carpet cleaner may also be used to

pick up small liquid spills (one gallon or less,

never to exceed 1/8” in depth). Do not submerge

unit in liquid.

Place the floor nozzle with the SpinScrub

mode

selector to SPILL PICK-UP in front of the spill, pull

the nozzle very slowly over the spill.

When finished picking up spills, follow “After

Cleaning” instructions.

CAUTION

! !

To reduce the risk of injury from moving parts,

unplug cleaner.

To prevent possible leaking, remove clean water tank

(Fig. 2.8) and Dirty Water Tank (Fig. 2.13). Set tanks

aside (do not set tank on furniture).

With handle in upright position, tilt cleaner back so

that handle rests on the floor.

CLEANING HARD FLOORS

How to Attach Squeegee for Hard Floor

Cleaning (Available on select models only)

Read “Before you begin cleaning” instructions on

page 9.

Do not use the carpet cleaner on unsealed

hardwood floors.

To prevent damage to wood floors, follow

the flooring manufacturer’s cleaning

recommendations.

If using cleaner on sealed wood floors, inspect

floor surface for worn finish, bare wood or

separated joints. It is not recommended to use

the cleaner on wood floors if any of these

conditions exist.

3.4

1. Fill clean water tank according to instructions for

Fig. 2.9.

2. Fill detergent container with HOOVER

Hard Floor

Cleaner according to instructions for Fig. 2.10.

3. Slide SpinScrub selector to GENTLE SCRUB.

4. Dry hands and plug cleaner into a properly

grounded outlet.

5. Step on handle release pedal and lower handle to

operating position.

6. Set Wash/Rinse Setting switch to WASH (Wash/

Auto-Rinse™ when available). Turn cleaner on.

7. To release solution, press trigger. Slowly move

cleaner forward and backward over area to be

cleaned. Water and detergent will be released on the

forward stroke. For models with Auto-Rinse feature,

a water-only rinse will automatically be released on

the reverse stroke.

8. To pick up dirty solution, release trigger and slowly

move cleaner over area where solution has just been

dispensed. Use both forward and reverse strokes.

9. If rinsing the floor is desired, set Wash/Rinse

Setting switch to RINSE. Repeat steps 7 & 8. This

setting provides a water-only rinse in both the

forward and reverse strokes.

Continue>>

CAUTION

! !

3.4 Position the squeegee, larger lip facing up, on

bottom of nozzle until it snaps securely into place.

Make sure the outside edges are pushed up tight

against the nozzle.

Remove squeegee to return to cleaning carpets.

CLEAN SURGE

BUTTON

(Available on select models only)

The Clean Surge

button can be used to dispense

extra solution when cleaning particularly soiled areas

of carpet or spots.

To use, press Clean Surge

button while squeezing

solution trigger. For normal solution spray, release

button and continue to squeeze solution trigger.

CAUTION

! !

Do not use the carpet cleaner to pick up

flammable or combustible liquids or chemicals.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hoover MaxExtract Deep Cleaner Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info