Bedienungsanleitung Horizon Hobby AR7210BX - BeastX (Seite 48 von 59) (Englisch)

606950

Zoom out

Zoom in

Vorherige Seite

1/59

Nächste Seite

If the maximum positive/negative pitch angle is changed at Setup Menu Point K then

also the hovering pitch will change! So after re-adjusting the maximum angles also

check and re-adjust the hovering pitch at Parameter Menu Point M.

When using the “3D — Mode with pitch control” make sure that the pitch range is

symmetrical, i.e. the maximum positive and negative pitch angles are of same size.

Otherwise the hovering pitch will differ in normal and inverted position as the hoving

pitch is calculated from the maximum pitch! The setting at Parameter Menu Point M

affects both directions. A separate adjustment of the hovering pitch angles is not provided.

Channel Assignment Menu

By default, the Spektrum AR7210BX and all additional features can be operated with a

6-channel transmitter. If desired, and a transmitter with 7 or more channels is used, SAFE

technology can be operated with a separate channel and you can assign a separate switch

channel for the Nitro Governor instead of controlling the RPM Governor by throttle channel.

Teaching the additional channels is done in the “Channel Assignment Menu”:

1. Press and hold the push button on the Spektrum AR7210BX unit and power it on.

Menu LED A will ﬂash instantly, the Status LED will either be Red (no transmitter

signal) or Blue (transmitter signal is there). Release the button.

2. At Menu Point A, the switch channel for the nitro RPM governor can be assigned.

Move the speciﬁc channel (switch or knob), the Blue Status LED will ﬂash shortly to

indicate the channel has been detected. Then press the button to proceed to Menu Point

B.Ifyoudon’twanttoassignaseparatechannel,eitheryoudon’tneedthisfunction

atallorifyouwanttousethethrottlechanneltocontrolthegovernor,don’tmoveany

channel but simply skip this assignment by brieﬂy pressing the button.

3. At Menu Point B, you can assign your separate channel for switching SAFE

technology.HereagainyoucansimplyskipbyPressingthebuttonandkeepthe

default setting (using combined mode with gear channel).

For these functions you can assign any channel from AUX2 to AUX6. Note that it is not possible

to assign both functions to the same channel. Also note that the speciﬁc AUX output on the unit

cannot be controlled by this channel then. Instead as a side effect the channel output will be

mapped to the next free channel internally, i.e. when not using the governor function and you

assign channel AUX2 to control the SAFE

technology, the AUX2 output on the unit then will be

mappedtothetransmitter’sAUX4channel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Horizon Hobby AR7210BX - BeastX Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Horizon Hobby AR7210BX - BeastX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info