606950
50
Zoom out
Zoom in
Vorherige Seite
1/59
Nächste Seite
EN
50
If SAFE
®
technology works reversed, e.g. one of the Menu-LEDs B through N lights up when
the switch for SAFE
®
technology is in “off”-position and the Menu-LED A does not disappear
independant of the servo throw when the switch is in “on”-position, then simply reverse the
channel for SAFE
®
technology in your transmitter by using the servo reverse function.
SAFE® Technology with Combined Switch Channel
The tail gyro gain channel is also used for SAFE
®
technology. In the switch position where
SAFE
®
technology is off, the channel deflection determines the amount of tail gyro gain as
usual. Increase or decrease the (servo) travel of channels to adjust the tail gyro gain. The
amount of tail gyro gain is indicated by the yellow Menu-LEDs each time after initialization
procedureandalwayswhenthegainchanges.HeretheStatusLEDlightsupBlue. When you
flip the switch and the channel is deflected to the other direction, the Spektrum AR7210BX will
keep the current tail gyro gain and activate SAFE
®
technology.HeretheStatusLEDlightsup
Red. When adjusting the height of deflection of the channel into this direction you can specify
the SAFE
®
technology gain by adjusting the servo travel. So here one channel is used for two
functions. Depending on the direction you can either adjust tail gyro gain or SAFE
®
technology
gain and by switching between directions SAFE
®
technology is activated or deactivated.
When using SAFE
®
technology with combined switch channel make sure
SAFE
®
technology is at least deactivated once before take off. Otherwise the
tail gyro gain would be minimal as the system would not have been able to determine your
tail gain adjustment after initialization.
In this mode it is absolutely necessary to use a switch that changes the control directions
directly and without intermediate steps. In particular, do not use a slider on the transmitter!
Otherwise, when you activate SAFE
®
technology the tail gyro sensitivity would be decreased to
0% before the system turns on the SAFE
®
technology. So you would have 0% of tail gyro gain
when SAFE
®
technology is active.
100%
-100%
0%
A
Menu-LEDs
Tail gyro gain channel
HeadingLock-Mode
(Status-LED: blue)
N M L K J I H G F E D C B
B C D E F G H I J K L M N
SAFE® Technology on
(Status-LED: red)
SAFE® Technology o
(Status-LED: red)
A
The tail gyro Rate-Mode is only available when SAFE® is operated with Separate Switch Channel.
50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Horizon Hobby AR7210BX - BeastX wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Horizon Hobby AR7210BX - BeastX

Horizon Hobby AR7210BX - BeastX Bedienungsanleitung - Deutsch - 64 seiten

Horizon Hobby AR7210BX - BeastX Bedienungsanleitung - Deutsch, Englisch - 176 seiten

Horizon Hobby AR7210BX - BeastX Bedienungsanleitung - Französisch - 57 seiten

Horizon Hobby AR7210BX - BeastX Bedienungsanleitung - Französisch - 176 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info