Bedienungsanleitung Horizon Hobby DX7 - 7 Channel DSMX Transmitter (Seite 33 von 50) (Englisch)

606949

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

33SPEKTRUM DX7 • TRANSMITTER INSTRUCTION MANUAL

V-Tail Differential



Only available in Sailplane Type when V-Tail A or V-Tail B is active. See SAIL (Sailplane) section for set up.

Camber Preset



Only available in Sailplane Type when a 2 aileron wing type is selected. See SAIL (Sailplane) section for set up.

Camber System



Only available in Sailplane Type when a 2 aileron wing type is selected. See SAIL (Sailplane) section for set up.

Flap System



Only available in Airplane Type when a ﬂ ap-enabled wing type is selected. See ACRO (Airplane) section for set up.

Pitch Curve



Only available in Helicopter Type. See HELI (Helicopter) section for set up.

Swashplate



Only available in Helicopter Type. See HELI (Helicopter) section for set up.

Gyro



Only available in Helicopter Type. See HELI (Helicopter) section for set up.

Tail Curve



Only available in Helicopter Type. See HELI (Helicopter) section for set up.

The following menu options are only available when they are enabled from the Model Type screen.

Mixing allows control input for a channel to affect more than one

channel at a time. Mixing functions support:

• Mixing a channel to another channel.

• Mixing a channel to itself.

• Assigning offset to a channel.

• Linking primary to secondary trim.

These mixes are available for each model memory:

Select a channel for master and slave. Inputs for the

master channel control both the master and slave channels. For

example, Elevator to Flap makes elevator the master channel and

ﬂ ap the slave channel.

Offset

Change the Offset value to move the effective center position

of the slave channel. Positive or negative value determines the

direction of the offset. Offset is not available for curve mixes.

Trim

If the master channel trim should also adjust the slave channel, set

Trim to Act. A channel monitor on the left side of the screen

shows how channels respond to input. To view a switch-assigned

mix on the monitor, the mix switch must be in the active position.

• 8 programmable mixes

• Cyclic to Throttle (HELI)

• Swashplate (HELI)

• Elevator to Flap (ACRO)

• Aileron to Rudder (ACRO)

• Rudder to Aileron/Elevator (ACRO).

• Aileron>Rudder (SAIL)

• Aileron>Flap (SAIL)

• Elevator>Flap (SAIL)

• Flap>Elevator (SAIL)

If you wish to assign a mix to a switch position:

1. Make sure you are in the desired mix screen.

2. Move the switch you want to assign the mix to.

3. Scroll to the switch position where you want the mix to be

active.

4. Press the scroll wheel to activate the mix. When the box is

ﬁ lled, the mix is active.

The mix is Active when the box is ﬁ lled and Inactive when the

box is open. You can assign a mix to be active in multiple switch

positions (0,1 or 2).

Tip: Use Auto Switch Select to select the switch.

CAUTION: Always do a Control Test of your model after

changing mixes.

FUNCTION LIST

Mixing

Assigning a Mix to a Switch

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Horizon Hobby DX7 - 7 Channel DSMX Transmitter Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Horizon Hobby DX7 - 7 Channel DSMX Transmitter

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info