Bedienungsanleitung Horizon Hobby DX7 - 7 Channel DSMX Transmitter (Seite 34 von 50) (Englisch)

606949

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

34 SPEKTRUM DX7 • TRANSMITTER INSTRUCTION MANUAL

Back Mixing applies a mix to all related servos in a wing or tail

type. For example, if you select 2 AIL, 2 FLAP in the Aircraft Type

screen, a mix to one aileron channel affects both aileron servos.

The mix response, however, depends on the aileron channel

included in the mix.

A Back Mix also enables you to use fewer mixes to achieve the

desired response, for example adding roll to a split elevator.

The Range Test function reduces the power output. This allows for

a range test to conﬁ rm the RF link is operating correctly. Perform

a range check at the beginning of each ﬂ ying session to conﬁ rm

system operation.

To Access the Range Test screen:

1. With the transmitter on and the main or telemetry screen

displayed, press the scroll wheel. The Function list displays.

2. Scroll to highlight Range Test, then press the scroll wheel to

access the Range Test function.

3. With the Range Test screen displayed, push and hold the

trainer button. The screen displays Reduced Power. In this

mode the RF output is reduced allowing for an operational

range test of your system.

4. If you let go of the trainer button, the transmitter will go back

to Full Power.

IMPORTANT: Telemetry alarms are disabled during the

Range Test.

Range Testing the DX7

1. With the model restrained on the ground, stand 30 paces

(approx. 90 feet/28 meters) away from the model.

2. Face the model with the transmitter in your normal ﬂ ying

position and place the transmitter into Range Test mode (see

above). Then push the trainer button; the power output will be

reduced.

3. Operate the controls. You should have total control of your

model with the transmitter in Range Test mode.

4. If control issues occur, contact the appropriate Horizon Product

Support ofﬁ ce for assistance.

5. If performing a range test while a telemetry module is active,

the display will show ﬂ ight log data.

The DX7 Timer function allows you to program a countdown timer

or stop watch (count up timer) to display on the main screen. An

alarm sounds when the programmed time is reached. You can

program the timer to start using the assigned switch position or

automatically when throttle is raised above a programmed position.

Two internal timers are available that show run time for a speciﬁ c

model displays on the Main Screen. A total system timer is also

available.

Press NEXT to select the Timer Event Alerts settings. These

include options for the alerts at every minute for down timers, 1

minute remaining alert, 30 seconds remaining alert, 10 second

to 1 second remining alerts, expiration alert, and every minute up

alert. Press NEXT again to select the Timer Control Alerts settings.

Available options include Timer Start alert, Timer Stop alert, and

Timer Reset alert.

FUNCTION LIST

Back Mixing

Range Test

Timer



Timer Event and Timer Control Alerts

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Horizon Hobby DX7 - 7 Channel DSMX Transmitter Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Horizon Hobby DX7 - 7 Channel DSMX Transmitter

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info