655857

Hormann HST - Side sectional door Seite 9

9
Zoom out
Zoom in
Vorherige Seite
1/136
Nächste Seite
• Check that the fixing materials supplied are suitable for
the given structural conditions.
• Always obtain the permission of the structural engineer
before fastening the door to supporting structural
elements.
• Ensure adequate water run-off in the area of the floor
rail and the frame parts, otherwise there is a danger of
corrosion.
• Ensure sufficient drying and ventilation in the building,
otherwise there is danger of corrosion.
• The door must be effectively protected before carrying
out plastering and paintwork, as splashes of mortar,
cement, plaster, paint etc. can damage the door
surface.
• Protect the door from caustic, aggressive substances,
e.g. nitrous reactions from stones or mortar, acids,
alkali solutions, de-icing salt, aggressive paints or
sealants. Failure to do so could lead to corrosion.
▶
To ensure simple and secure fitting, please follow
the work steps listed in the illustrated section.
4 Operation
4.1 Door operation
WARNING
Danger of injury due to door travel
The side sectional door closes horizontally; persons or
objects may be trapped.
▶
When in operation, make sure that neither persons,
children in particular, nor objects are located within
the door's area of travel.
▶
Always keep the opening area of the door clear.
▶
Do not operate the door in strong winds.
The door must only be operated by suitably instructed
persons. If the side sectional door is competently fitted
and inspected, it can be easily moved and operated.
4.1.1 Manually operated doors
Note the separate fitting instructions for manually operated
doors (see Figures2.6a / 2.6b and 4a.2 / 4b.2).
WARNING
Danger of injury due to improper operation
Persons or objects may be trapped if the door is
operated improperly.
▶
Only open and close the door using the supplied
operating elements; these ensure a controlled,
smooth action.
▶
When closing the door, make sure that the latches
engage fully and correctly.
4.1.2 Power-driven doors
The automation of a door requires that special safety
regulations be observed.
Consult your supplier.
CAUTION
Danger of crushing between the door and wall
Crushing may occur if the space between the automated
door in the open end-of-travel position and the rear
garage wall is ≤500mm.
▶
In this case, fit a buffer sealing to the last section as
well (see Figure4a.6 / 4b.5).
5 Cleaning and Care
ATTENTION
Scratches on the panes due to improper cleaning
Rubbing the panes causes scratches.
▶
Dirt and dust particles must first be thoroughly rinsed
off with water. If necessary, only wash with water, a
pH-neutral household detergent and a soft, clean
cloth.
Clear water is sufficient for cleaning and care. Use
warm water together with a neutral, non-abrasive cleaning
agent (household detergent, pH value 7) if more heavily
soiled. To preserve the surface characteristics, regular
cleaning must be carried out at least every 3 months
(outside of door, seals). The slide area behind the side
seals must be kept permanently clean so that it offers a
smooth sliding surface.
A variety of environmental influences (e.g. maritime
climate, acids, road salt, air pollutants, paint damage) may
make additional protective coating necessary (seePaint
treatment on page10).
6 Inspection and Maintenance
6.1 Inspections and maintenance
WARNING
Danger of injury due to defective safety components
Important safety components may fail or become
defective if not sufficiently inspected and maintained.
▶
Have a qualified person perform inspection and
maintenance work at regular intervals.
The following inspection and maintenance tasks must be
carried out by a specialist in accordance with these
instructions, before initial operation and at least once a
year.
6.1.1 Fixing points
▶
Check all the fixing points on the door and the building
structure and make sure that all the fastenings are
securely seated and, if necessary, retighten.
6.1.2 Rollers and tracks
Rollers must rest evenly on the track (see Figure6).
▶
Adjust rollers if necessary. Observe the operator fitting
notes; they contain details on roller adjustment.
▶
Clean tracks, if necessary, do not grease!
4004769 HST RE / 09.2015
9
ENGLISH
… 9 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hormann HST - Side sectional door wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Hormann HST - Side sectional door

Hormann HST - Side sectional door Zusatzinformation - Alle Sprachen - 136 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info