Bedienungsanleitung Hormann Schuifhekaandrijving (Seite 32 von 132) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

538730

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

Behaviour following a power failure9.2

Once the power supply has been restored, the gate must be

reengaged with the operator upstream from the limit switch.

Slightly lift the motor when turning the mechanism to the f

lock position (see Figure 11.2).

A necessary reference run following a power failure is

automatically performed if an impulse command is

pending.

During this reference cycle the option relay clocks and a

connected warning light ﬂashes slowly.

Inspection and Maintenance10

The sliding gate operator is maintenance-free. The gate

system must be checked by a specialist in accordance with

the manufacturer's speciﬁcations.

NOTE:

Inspection and maintenance may only be carried out by a •

qualiﬁed person. Contact your supplier for this purpose.

A visual inspection may be carried out by the owner. If •

repairs become necessary, please contact your supplier.

We would like to point out that any repairs not carried out

properly or with due professionalism shall render the

warranty null and void.

Check the function of the 8k2 resistance contact strips •

twice a year.

Operation, error and warning messages10.1

LED GN10.1.1

The green LED (Figure 4) indicates the operating state of the

control:

Steady illumination

Normal state, all OPEN end-of-travel positions and forces

learned.

Fast ﬂashing

Force learning cycles must be performed.

Slow ﬂashing

Set-up mode – end-of-travel setting

When setting up the reversal limits

(see Reversal limit, page 28)

Flashing frequency is proportional to the selected •

reversal limit

Minimum reversal limit: LED is permanently off•

Maximum reversal limit: LED is permanently on•

LED RD10.1.2

The red LED (Figure 4.1) indicates:

In set-up mode

Limit switch actuated = LED is on•

Limit switch not actuated = LED is off•

Radio programming display

Flashing as described in Programming the hand transmitter

buttons on an integral radio receiver on page 31

Display of the button inputs, radio

Actuated = LED is on•

Not actuated = LED is off•

In normal operation:

Flashing code as an error/diagnosis display

Error/diagnosis display

The red LED RD helps to easily identify causes when

operation does not go according to plan.

Display ﬂashes 2x

Error/warning

Safety/protective device has responded

Possible cause

Safety/protective device has been actuated•

Safety/protective device defective•

Without the SE1, 8k2 resistance between terminal 20 •

and 72 missing

Without the SE2, 8k2 resistance between terminal 20 •

and 73 missing

Without the SE3, wire jumper between terminal 20 and •

71 missing

Remedy

Check safety/protective device•

Check whether the appropriate resistance/wire •

jumpers are present without the connected safety/

protective device

Display ﬂashes 3x

Error/warning

Force limit in CLOSE direction

Possible cause

Obstruction in gate area

Remedy

Remove obstruction; check forces, if necessary, increase

Display ﬂashes 4x

Error/warning

Hold or static current circuit is open, operator at a standstill

Possible cause

Normally closed contact at terminal 12/13 is open•

Electric circuit interrupted•

Remedy

Close contact•

Check electric circuit•

Display ﬂashes 5x

Error/warning

Force limit in OPEN direction

Possible cause

Obstruction in gate area

Remedy

Remove obstruction; check forces, if necessary, increase

Display ﬂashes 6x

Error/warning

System error

Possible cause

Internal error

Remedy

Restore the factory setting (see Radio Remote Control,

page 30), repeat the learning procedure for the control

system and replace, if necessary

TR10A059-C RE / 10.2008

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hormann Schuifhekaandrijving Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info