Bedienungsanleitung Hot Spring SOVEREIGN - II (Seite 21 von 48) (Englisch)

624652

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Page 18

operatInG InStructIonS

Standard lcd control panel

(All models except GRANDEE & ENVOY)

The control panel provides a quick visual check of the spa’s status and

allows the user to set the temperature, activate the jets & lights, lock the

temperature and/or spa functions. Other optional functions may also be

available depending on the spa model and accessory equipment that

has been installed into the spa. The control panel has eight buttons.

HARD BUTTONS

The four labeled outer buttons are referred to as "Hard buttons". These

buttons are fixed and their functions do not change.

JETS - If jet pump indicator icons is off and JETS hard button is

pressed, the 1st jet pump function will activate and the control panel

display will advance to the Jets menu.

If jet pump indicator

icons

is on and the JETS hard button is pressed

while in any screen other than the Jets menu, the jets pump function

does not change, only the control panel screen will change to the Jets

menu.

LIGHTS - If lights are off, press LIGHTS hard button from any screen to

turn on the Underwater lights (only) and display the Underwater Lighting

menu. When LIGHTS hard button is pressed in the Underwater Lighting

menu with the underwater lights on, it will cycle the light intensity for the

underwater lights. If underwater lights are on, initial press of LIGHTS

hard button will not change light setting but will access Underwater

lighting menu.

OPTIONS - Transitions to the Options screen to access temperature

and setup menu

BACK - Goes back one menu. In Home screen Hold BACK button until

screen rotates 180° to view from inside spa. Repeat to reverse.

SOFT BUTTONS

The four inside buttons are referred to as "soft buttons". Pressing a soft

button will activate the function on the control panel screen closest to

that button. The control panel display lets you know you’ve pressed a

button and that the selected function has been performed. After a period

of non-use (45 seconds) the display will go back to the Home screen

where the screen will remain on for several minutes before going into

sleep mode. Pressing any button will wake up a sleeping display.

INDICATOR ICONS

The indicator icons can only be seen on the Home Screen. They are

visible whenever the icon's function is active.

READY Indicator: The READY indicator icon will light when

the spa water temperature is within 2°F (1°C) of the set

temperature, and will turn off when the temperature is outside of that

range. If you increase or decrease the temperature setting of the spa,

the ready indicator will turn off until the water temperature reaches the

acceptable range for the new temperature setting. A flashing READY

indicator means a problem may exists with the temperature sensor (see

Troubleshooting section for more information)

Spa Light Indicator: The Spa Light indicator icon is displayed

when any light inside the spa is on. The indicator will remain

solid as long as any light is activated. Spa Light indicator flashes

whenever the color wheel is on.

Spa or Temperature Lock Indicator: The Spa or Temperature

Lock indicator icon is displayed when either the Spa Lock,

Temperature Lock or both is activated. Lock indicator icon does not

flash.

Jet Pump Indicator: The Jet Pump indicator icon is displayed

whenever a jet pump is on. The Jet Pump indicator icon will

flash whenever the spa is in the ten-minute clean cycle.

Summer Timer Indicator: The Summer Timer indicator icon is

displayed when the summer timer is set to ON. In the summer

timer mode, the heater and circulation pump cycle are off for eight

hours. The Summer Timer indicator icon will not flash.

Water Care Indicator: The Water Care indicator icon is

displayed whenever a water care device is detected in the

system and the water care system is operating correctly. The icon will

flash if the water care system requires attention.

POWER Indicator: The POWER indicator icon is displayed

when the spa is properly supplied with power. It also provides

a diagnostic function–a flashing Power indicator icon indicates that the

heater high limit has tripped, meaning that either the spa water is above

its acceptable temperature range, or a malfunction has occurred within

the spa (such as low circulation due to clogged filters). An ‘off’ power

indicator icon means that there is a problem with the spa control box or

the power supplied to the spa (see Troubleshooting section for more

information).

OPTION SCREEN

The Option screen is an intermediate

screen that gets you to various

optional settings.

Press the OPTIONS hard button

on the control panel to display the

Options screen.

Press the Soft button next to

the descriptions to access the

description's screen.

IMPORTANT: Audio and ACE Water Care will only be displayed on your

Options screen if your spa is equipped with these features.

Operating Instructions

JETS

Hard button

Soft buttons

Indicator Icons

Control panel screen

LIGHTS

Hard button

OPTIONS

Hard button

BACK

Hard button

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hot Spring SOVEREIGN - II Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info