Bedienungsanleitung Hotpoint-Ariston LFD 11M132 (Seite 18 von 28) (Englisch, Italienisch)

570818

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Installation

* Only available in selected models.

If the appliance must be moved at any time, keep it in an

upright position; if absolutely necessary, it may be tilted onto

its back.

Connecting the water supply

Adaptation of the water supply for installation should only

be performed by a qualified technician.

The water inlet and outlet hoses may be positioned towards

the right or the left in order to achieve the best possible

installation.

Make sure the dishwasher does not bend or squash the hoses.

Connecting the water inlet hose

• Toa3/4”gascoldor hotwater connectionpoint(max.

60°C).

• Runthewateruntilitisperfectlyclear.

• Screwtheinlethosetightlyintopositionandturnoffthe

tap.

If the inlet hose is not long enough, contact a specialist

store or an authorised technician

(seeAssistance)

The water pressure must be within the values indicated

in the Technical Data table - otherwise the dishwasher may

be function properly.

Make sure the hose is not bent or compressed.

Connecting the water outlet hose

Connect the outlet hose to a drain duct with a minimum

diameterof2cm.(A)

The outlet hose connection must be at a height ranging from

40to80cmfromthefloororsurfacewherethedishwasher

rests.

Before connecting the water outlet hose to the sink drain,

removetheplasticplug(B).

Anti-flooding protection

To ensure floods do not occur, the dishwasher:

- is provided with a special system which blocks the water

supply in the event of anomalies or leaks from inside the

appliance.

Somemodelsare alsoequipped withthe supplementary

safety device New Acqua Stop*, which guarantees anti-

flooding protection even in the event of a supply hose rupture.

WARNING: HAZARDOUS VOLTAGE!

Under no circumstances should the water inlet hose be cut

as it contains live electrical parts.

Electrical connection

Before inserting the plug into the electrical socket, make

sure that:

• Thesocketisearthed and complies with current

regulations;

• thesocketcan withstandthe maximumload ofthe

appliance as shown on the data plate located on the inside

of the door

(seechapterDescriptionoftheappliance);

• Thepowersupplyvoltagefallswithinthevaluesindicated

on the data plate on the inside of the door.

• Thesocketiscompatiblewiththeplugoftheappliance.If

this is not the case, ask an authorised technician to replace

theplug(

see Assistance

).Donotuseextensioncablesor

multiple sockets.

Once the appliance has been installed, the power supply

cable and the electrical socket should be easily accessible.

The cable should not be bent or compressed.

If the power supply cable is damaged, have it replaced

by the manufacturer or its authorised Technical Assistance

Serviceinordertopreventallpotentialhazards.

(See

Assistance)

The Company shall not be held responsible for any

incidents, if these regulations are not observed.

Positioning and levelling

1. Position the dishwasher on a level sturdy floor. If the floor is

uneven, the front feet of the appliance may be adjusted until

itreachesahorizontalposition.Iftheapplianceislevelled

correctly, it will be more stable and much less likely to move

or cause vibrations and noise while it is operating.

2. Before recessing the dishwasher, stick the adhesive

transparent strip* under the wooden shelf in order to protect

it from any condensation which may form.

3.Placethedishwashersothatitssidesorbackpanelarein

contact with the adjacent cabinets or the wall. This appliance

can also be recessed under a single worktop*

(seethe

Assembly instruction sheet)

4*.Toadjusttheheightoftherearfoot,turntheredhexagonal

bushing on the lower central part at the front of the dishwasher

usingahexagonalspannerwithanopeningof8mm.Turnthe

spanner in a clockwise direction to increase the height and

in an anticlockwise direction to decrease it.

(seeBuilding-in

instruction sheet attached to the documentation)

MIN 40 cm

MAX 80 cm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint-Ariston LFD 11M132 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hotpoint-Ariston LFD 11M132

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info