Bedienungsanleitung HP Aruba IAP-304 (Seite 7 von 11) (Englisch)

724190

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

Aruba 300 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide 7

Configuring the 300 Series Access Points

Access Point Provisioning/Reprovisioning

Provisioning parameters are unique to each access point. These local access point parameters are initially configured on the

controller which are then pushed out to the access point and stored on the access point itself. Aruba recommends that

provisioning settings be configured via the ArubaOS Web UI only. Refer to the ArubaOS User Guide for complete details.

Access Point Configuration

Configuration parameters are network or controller specific and are configured and stored on the controller. Network

configuration settings are pushed out to the access point but remain stored on the controller.

Configuration settings can be configured via the ArubaOS Web UI or ArubaOS CLI. Refer to the ArubaOS User Guide for

complete details.

Electrical and Environmental Specifications

For additional specifications on this product, please refer to the product data sheet at www.arubanetworks.com/

safety_addendum.

Electrical

 Ethernet:

 One 100/1000 Base-T auto-sensing Ethernet RJ45 interface

 Power over Ethernet IEEE 802.3at 56VDC (nominal) and 802.3af 48VDC (nominal).

 Power:

 Maximum (worst-case) power consumption: 13.5W (802.3af PoE) or 12W (DC)

 Excludes power consumed by external USB device (and internal overhead); this could add up

to 6W (PoE) or 5.5W (DC) for 5W/1A USB device

 Direct DC source: 12Vdc nominal, +/- 5%

 Power over Ethernet (PoE): 802.3at and 802.3af complaint source

 Connect only to IEC 60950-1 or IEC 60601-1 3rd edition products and power sources.

Environmental

 Operating:

 Temperature: 0°C to +50°C (+32°F to +122°F)

 Humidity: 5% to 93% non-condensing

 Storage and transport:

 Temperature: -40°C to +70°C (-40°F to +158°F)

Regulatory Information

The following regulatory model names apply to the 300 Series access points:

The instructions for this section are applicable to the AP-304 and AP-305 only.

All Aruba access points should be professionally installed by an Aruba Certified Mobility Professional (ACMP). The installer is

responsible for ensuring that grounding is available and meets applicable national and electrical codes.

Tous les points d'accès Aruba doivent impérativement être installés par un professionnel agréé. Ce dernier doit s'assurer

que l'appareil est mis à la terre et que le circuit de mise à la terre est conforme aux codes électriques nationaux en vigueur.

If a power adapter other than the Aruba-approved adapter is used in the US or Canada, it should be NRTL listed, with an

output rated 12Vdc, minimum 2A, marked “LPS” and “Class 2”, and suitable for plugging into a standard power receptacle in

the US and Canada.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

HP Aruba IAP-304 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info