20128
74
Zoom out
Zoom in
Vorherige Seite
1/82
Nächste Seite
67
D
Frequently Asked Questions About
USB (Universal Serial Bus)
Note: If you are a Windows 2000 Professional user, visit HP’s web site at
http://www.hp.com/cposupport/eschome.html for more information.
What is the problem? Possible cause To solve the problem…
During installation,
when I connect a USB cable
between the printer and my
computer, the “New
Hardware Wizard” message
did not appear.
You may not be using
Windows 98.
Make sure Windows 98 is running and your computer
is connected using a USB cable. If you do not have
Windows 98, you need to use a parallel cable.
You may not have USB
enabled.
1 In Windows 98, click Start Settings Control
Panel.
2 Double-click the System icon.
3 Click the Device Manager tab.
4 Click the plus ( + ) icon next to the Universal Serial
Bus Controller option. If you see a USB host
controller and a USB root hub listed, USB is
probably enabled. If you do not see these devices
listed, refer to your computer’s documentation or
contact the manufacturer for more information
on enabling and setting up USB.
5 If you cannot enable USB, you can always use a
parallel cable to connect your printer to your
computer.
Your USB cable may not
be connected properly.
1 Disconnect and then reconnect the USB cable
from your printer.
2 Make sure that it is securely attached.
During installation,
when I connect a USB cable
between the printer and my
computer, an “Unknown
device” message appears.
Static electricity has
built up in the cable
between your
computer and printer.
OR
You may have a
defective USB cable.
1 Disconnect the USB cable from your printer.
2 Unplug the printer from its power cable.
3 Wait approximately 30 seconds.
4 Plug the power back into the printer.
5 Plug the USB cable back into the printer.
6 If “Unknown device” continues to appear in the
“New hardware found” dialog, replace the USB
cable or use a parallel cable.
970C.book Page 67 Tuesday, February 1, 2000 11:31 PM
74

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für HP DESKJET970C wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info