20128
75
Zoom out
Zoom in
Vorherige Seite
1/82
Nächste Seite
68
D
During installation,
when I connect a USB cable
between the printer and my
computer, the “New
Hardware Wizard” message
appeared once, but the
printer did not install, and
now “New Hardware Wizard”
will not appear again.
Installation was
cancelled or had an
error.
1 Select Start Settings Printers.
2 Double-click on Add Printer.
3 Click Next.
4 Click Next.
5 Click Have Disk.
6 Click Browse, then browse to the printer software
CD.
7 Browse to the language code folder. For a list of
language codes, see page 66.
8 Double-click 9xinf folder, then click OK.
9 Click OK.
10 Click Next.
11 In the list of ports you want to use with this
printer, select USB/DeskJet 970C/<printer serial
number>.
12 Click Next.
13 Click Next.
14 Click Finish.
My printer is
connected with a USB cable
through another USB device
or a hub and when I try to
print I get a message saying
“There was an error writing to
<name of USB port>.”
Your printer may not be
getting good data from
the other device or hub.
Connect the printer directly to the USB port on the
computer.
I have a USB cable,
and when I try to print I get a
message saying “There was
an error writing to LPT1.”
You may not have
plugged your USB cable
in before installing the
software.
1 Disconnect the USB cable from your printer.
2 Insert the printer software CD (or Disk 1 if you
have diskettes) into your computer.
3 Click Start Run.
4 Browse the CD, select Setup, then click Open.
5 The setup.exe file will appear in the dialog box.
Click OK.
6 Select the Remove HP DeskJet 970C Series
software option to remove the software.
7 Connect the USB cable to your printer again. The
USB installation screen should appear again.
8 Repeat the “Install USB Software” step. See your
Quick Start Poster or page 56 in this User’s Guide.
The printer is really slow
You may be
using a USB cable and
other USB devices are in
use.
1 Attach the printer’s USB cable directly to the
computer, rather than at the end of a daisy chain.
2 Avoid using other devices in the daisy chain while
printing.
What is the problem? Possible cause To solve the problem…
970C.book Page 68 Tuesday, February 1, 2000 11:31 PM
75

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für HP DESKJET970C wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info