Bedienungsanleitung HP Elite Slice (Seite 10 von 30) (Englisch)

655054

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

●

If the system does not boot, press and hold any key. If the system beeps, then the keyboard is operating

correctly.

●

Check all cable connections for loose connections or incorrect connections.

●

Wake the computer by pressing any key on the keyboard or pressing the power button. If the system

remains in sleep mode, shut down the computer by pressing and holding the power button for at least

four seconds. Then press the power button again to restart the computer. If the system will not shut

down, unplug the power cord, wait a few seconds, and then plug it in again. The computer will restart if

automatic start on power loss is set in Computer Setup. If the computer does not restart, press the

power button.

●

Recongure your computer after installing a non-Plug and Play expansion board or other option.

●

Be sure that all the needed device drivers have been installed. For example, if you are using a printer,

you need a driver for that printer model.

●

Remove any bootable media (CD/DVD or USB device) from the system before turning it on.

●

If you have installed an operating system other than the factory-installed operating system, check to be

sure that it is supported on the system.

CAUTION: When the computer is plugged into an AC power source, there is always voltage applied to the

system board. To reduce the risk of system board or component damage, always disconnect the power cord

from the power source before opening the computer.

Blink or beep codes: Interpreting POST diagnostic rear panel LEDs and audible codes

If you see ashing LEDs on the rear of the computer or if you hear beeps, see the Maintenance and Service

Guide (English only) for interpretation and recommended action.

HP Support Assistant

HP Support Assistant is an HP application that helps you maintain the performance of your computer and

resolve problems through automated updates and tune-ups, built-in diagnostics, and guided assistance. HP

Support Assistant is preinstalled on all HP or Compaq computers with Windows 7.

To access HP Support Assistant in Windows 7, double-click the HP Support Assistant icon on your desktop.

Using HP PC Hardware Diagnostics

HP PC Hardware Diagnostics is a Unied Extensible Firmware Interface (UEFI) that allows you to run diagnostic

tests to determine whether the computer hardware is functioning properly. The tool runs outside the

operating system so that it can isolate hardware failures from issues that are caused by the operating system

or other software components.

When HP PC Hardware Diagnostics (UEFI) detects a failure that requires hardware replacement, a 24-digit

Failure ID code is generated. This ID code can then be provided to support to help determine how to correct

the problem.

NOTE: To start diagnostics on a convertible computer, your computer must be in notebook mode and you

must use the keyboard attached.

To start HP PC Hardware Diagnostics (UEFI), follow these steps:

1. Turn on or restart the computer, and quickly press esc.

2. Press f2.

The BIOS searches three places for the diagnostic tools, in the following order:

4 Chapter 1 Getting Started in Windows 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

HP Elite Slice Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von HP Elite Slice

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info