Bedienungsanleitung HP Photosmart 2570 (Seite 113 von 142) (Englisch)

584741

113

Zoom out

Zoom in

Vorherige Seite

1/142

Nächste Seite

The Digital Imaging Monitor does not appear in the system tray

Solution If the Digital Imaging Monitor does not appear in the system tray

(normally located at the lower-right corner of the desktop), start the HP Solution

Center to check whether or not the essential icons are there.

For more information about missing essential buttons in the HP Solution Center,

see Some of the buttons are missing in the HP Solution Center (Windows).

The system tray normally appears in the lower-right corner of the desktop.

Uninstall and reinstall the software

If your installation is incomplete, or if you connected the USB cable to the computer

before prompted by the software installation screen, you might need to uninstall and

then reinstall the software. Do not simply delete the HP All-in-One program files from

your computer. Make sure to remove them properly using the uninstall utility provided

when you installed the HP Image Zone software.

A reinstall can take from 20 to 40 minutes. There are three methods to uninstall the

software on a Windows computer, and one method to uninstall on a Mac.

To uninstall from a Windows computer, method 1

1. Disconnect your HP All-in-One from your computer. Do not connect the HP All-in-

One to your computer until after you have reinstalled the software.

2. Press the On button to turn off the HP All-in-One.

3. On the Windows taskbar, click Start, Start Programs or All Programs (XP),

Hewlett-Packard, HP Photosmart 2570 All-in-One series, Uninstall.

4. Follow the onscreen instructions.

5. If you are asked whether you would like to remove shared files, click No.

Other programs that use these files might not work properly if the files are deleted.

6. Restart your computer.

Note It is important that you disconnect your HP All-in-One before

restarting your computer. Do not connect the HP All-in-One to your

computer until after you have reinstalled the software.

7. To reinstall the software, insert the HP All-in-One CD-ROM into the CD-ROM

drive on your computer, and follow the onscreen instructions and the instructions

provided in the Setup Guide that came with your HP All-in-One.

8. After the software is installed, connect the HP All-in-One to your computer.

9. Press the On button to turn the HP All-in-One on.

After connecting and turning on your HP All-in-One, you might have to wait

several minutes for all of the Plug and Play events to complete.

10. Follow the onscreen instructions.

When the software installation is complete, the HP Digital Imaging Monitor icon

appears in the Windows system tray.

To verify that the software is properly installed, double-click the HP Solution Center

icon on the desktop. If the HP Solution Center shows the essential icons (Scan

Picture and Scan Document), the software has been properly installed.

Chapter 13

110 HP Photosmart 2570 All-in-One series

Troubleshooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

HP Photosmart 2570 Seite 113

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von HP Photosmart 2570

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info