Bedienungsanleitung HP PSC-1417 (Seite 44 von 64) (Englisch)

480838

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Uninstall and reinstall the software

If your installation is incomplete, or if you connected the USB cable to the computer before being

prompted by the software installation screen, you might need to uninstall and then reinstall the

software. Do not simply delete the HP All-in-One program files from your hard drive. Make sure

to remove them using these instructions.

A reinstall can take from 20 to 40 minutes for both Windows and Mac computers.

To uninstall from a Windows computer, preferred method

1. Disconnect your HP All-in-One from your computer. Do not connect the HP All-in-One to

your computer until after you have reinstalled the software.

2. Click Start, Start Programs or All Programs (XP), Hewlett-Packard, HP PSC 1400 All-in-

One series, uninstall software and follow the instructions.

3. Click No if you are asked to remove shared files.

4. Restart your computer.

5. To reinstall the software, use the HP All-in-One CD-ROM and follow the instructions

provided in the Setup Guide.

6. After the software is installed, connect the HP All-in-One to your computer and press the

On / Resume button. You might have to wait several minutes for all of the Plug and Play

events to complete.

When the software installation is complete, the Status Monitor icon appears in the Windows

system tray.

To verify that the software is properly installed, double-click the HP Solution Center icon on the

desktop. If the HP Solution Center shows the key icons (Scan Picture, Scan Document, and

HP Image Zone), the software has been properly installed.

To uninstall from a Windows computer (alternate method)

1. Run the HP PSC 1400 All-in-One series software Setup program from the CD-ROM.

2. Select Uninstall and follow the onscreen directions.

3. Disconnect your HP All-in-One from your computer. It is important that you disconnect your

HP All-in-One before restarting your computer. Do not connect the HP All-in-One to your

computer until after you have reinstalled the software.

4. Restart your computer.

5. Run the HP PSC 1400 All-in-One series software Setup program again.

6. Launch Reinstall.

7. Follow the onscreen instructions and the instructions provided in the Setup Guide that came

with your HP All-in-One.

To uninstall from a Mac computer

1. Disconnect the HP All-in-One from your Mac.

2. Double-click the Applications: HP All-in-One Software folder.

3. Double-click HP Uninstaller.

Follow the onscreen instructions.

4. After the software is uninstalled, disconnect your HP All-in-One, and then restart your

computer. It is important that you disconnect your HP All-in-One before restarting your

computer. Do not connect the HP All-in-One to your computer until after you have

reinstalled the software.

5. Insert the HP All-in-One CD-ROM into the CD-ROM drive.

6. On the desktop, open the CD-ROM and then double-click HP all-in-one installer.

7. Follow the onscreen instructions and the instructions provided in the Setup Guide that came

with your HP All-in-One.

Chapter 9

40 HP PSC 1400 All-in-One series

Troubleshooting information

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

HP PSC-1417 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von HP PSC-1417

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info