Bedienungsanleitung HQ Power VPASG100 - Saigor 100 (Seite 4 von 19) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

622378

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

VPASGx00

11.05.2010 ©Velleman nv

• Switch on the amplifier last and switch it off first. Disconnect from the mains when not in use or when

maintenance activities are performed. Handle the power cable by the plug only.

• Keep power cables away from signal cables to avoid interference.

• Save this user manual for further reference.

4. Overview and use

Refer to the illustration on page 2 of this manual.

1 Clip LED This LED flashes when the channel A output signal is distorted.

2 Gain control: channel A Adjust the volume of channel A.

3 Power LED This LED illuminates when the amplifier is switched on.

4 Protect LED On when one of the internal protection circuits is active or no speakers are

connected. Switch off the amplifier and resolve the error condition .

5 Gain Control: channel B Adjust the volume of channel B.

6 Clip LED This LED flashes when the channel A output signal is distorted.

7 Power switch Press this button to start operation.

8 Speakon

output Speakon

speaker jack sockets.

9 TRS input sockets for input signals using balanced ¼”

RS (stereo) jacks

10 RCA input sockets for input signals using unbalanced phone (RCA) input jacks

11 Ground lift switch Some connected equipment may present hum. This switch will remove the

signal ground and reduce the effect of the mains hum.

12 TRS output sockets for output signals using stereo jacks

13 screw outputs for output signals using bare wires

14 fuse holde

Only replace the fuse when the device is disconnected from the

Mains. Only use fuses of the same rating and power.

15 AC power socket plug the AC power cord into this power socket

16 AC voltage selecto

Make sure the setting matches your local mains voltage!

5. Notes

• Rack installation

This amplifier can be mounted in a 19” (483mm) rack that allows access to front and rear panel. Make

sure to leave enough space around the device for sufficient ventilation. Note that when mounting in a

rack, the heaviest devices should be mounted closest to the bottom.

Also note that it is not enough to mount the amplifier with 4 screws on the front; the rear must also be

attached to the side bars of the rack.

• Input cables

Using short cables will improve sound quality as high frequencies are absorbed by the cable. Longer

cables may also lead to humming and noise problems. If you do need longer cables, only use balanced

cables.

• Output cables

The high damping factor of the amplifier produces a clear sound reproduction. Long and thin cables will

influence this damping factor and thus the low frequencies in a negative way. To maintain good sound

quality, the damping factor should be around 50. When long cables are unavoidable, make sure they

are thick enough.

• Speakers

Connect your speakers using the Speakon

or screw outputs. Connect the red terminator with the

positive wire and the black terminator with the negative wire.

• Ground lift switch

This switch allows the signal ground or chassis ground to be separated in case of a ground conflict. For

safety reasons it is recommended to keep the switch in the GND FLOATING position unless ground

problems are experienced.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

HQ Power VPASG100 - Saigor 100 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info