Bedienungsanleitung Hunter ACC (Seite 23 von 100) (Englisch)

685907

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

Some other brands or models of flow sensors may be

compatible with the ACC controller. One known-compati-

ble model is Data Industrial model IR-220B (also sold as

Hunter model GENDATFL).

NOTE: The ACC flow sensor connection is a 20 VDC pulsed

output which senses interruptions as “clicks”. It is DC

voltage, and the polarity must be observed.

The red + terminal corresponds to the red wire on the HFS

sensor, and if connecting to other brands of sensor insure

that correct polarity is observed.

Connect the positive (+) wire to the red Flow terminal on

the Master Module, and the negative (–) wire to the black

terminal.

ConneCTInG oTher floW sensors ............................................

The ACC controller has an integrated SmartPort

‚ on

the cabinet’s upper left side, or inside the front panel of

the plastic pedestal. This connection is automatically

compatible with Hunter ICR and SRR remote receivers.

To connect: remove the weather-resistant rubber cover

(metal cabinet versions), align the remote receiver’s

pins with the mating receptacle, and push firmly until

the receiver is fully seated. If the ET System adapter is

installed, plug the receiver into the mating connector on the

adapter.

If the receiver address is to be changed, hold in the green

button while plugging the receiver into the SmartPort, in

accordance with the ICR instructions.

Refer to the remote control’s instructions for additional

addressing and operations. However, there are some

significant differences in operating the remotes with the

ACC controller, from previous Hunter controllers.

When a program or station is started by ICR, the ACC

display will (as always) show why the program or station is

running. Remote starts are followed by “ICR” in the display

(Fig.1).

To set up an ICR remote control for operations with ACC,

consult the ICR instructions. Use the Mode button on the

ICR transmitter to select a station size of “240” to allow

access to all ACC programs and stations. Only ICR Remotes

manufactured September 2006 or later are compatible with

ACC. If you have an older ICR remote, the maximum station

size is 48. Therefore, if you are using an older remote and

an ACC decoder controller, the highest station you will be

able to control is station 48. You must obtain a newer ICR

to operate correctly with any ACC controller.

MULTIPLE STATIONS SIMULTANEOUSLY

ACC is an overlapping controller, and will allow up to

6 stations to run simultaneously. While other Hunter

controllers will stop existing stations when a new ICR

remote start command is received, the ACC will continue to

run existing stations along with the new stations, until the

maximum of 6 events has been reached (Fig. 2). If 6 events

are running and an ICR command is received to start another,

the command will be ignored. No new remote commands will

be accepted until one of the 6 events times out.

ICr remoTe ConTrol .................................................................

Figure 1

Figure 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hunter ACC Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hunter ACC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info