Bedienungsanleitung Husky FSS2H (Seite 11 von 16) (Englisch, Holländisch)

809496

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Troubleshooting

Before calling Technical Support, please check the following points; you may be able to solve any

problem yourself.

Problem

The chiller does not

work properly.

The chiller’s internal

temperature is too

high or too low.

The chiller is noisy in

operation or makes

unusual noises.

• Note: It is normal to

hear some noises as

refrigerant flows through

the compressor.

Outer surfaces are wet

Inner surfaces are wet

Possible Cause

The chiller is not plugged in.

The plug and/or the power cable

are faulty.

The fuse has blown.

The chiller is faulty.

The wrong temperature is selected.

The factory default settings for the

controller are incorrect.

The condenser is blocked by an

accumulation of dust.

The doors are not fully closed.

The chiller is close to a heat source

or the ambient temperature is too

high.

The ventilation grille is blocked.

The chiller is not on a level, firm

surface, or the unit may be touching

other items.

The chiller is vibrating against a

neighbouring object.

Chiller may be close to a water

source or leak.

The door may be opened too often

or kept open too long.

Action

Connect the plug to the

power supply

Call your supplier or a

qualified engineer.

Replace the fuse with one of

the same rating.

Call your supplier or a

qualified engineer.

Check the controller and

adjust the set temperature.

Call your supplier or a

qualified engineer.

Clean using a vacuum cleaner

and soft brush attachment

Check the unit is level and

the seals are not damaged.

Move the chiller to a better

location and check it is out of

direct sunlight.

Move the chiller to improve

free movement of air.

Check location and position

using a spirit level.

Relocate the chiller or the

object.

Dry surfaces thoroughly and

move the chiller.

Try to minimise opening of

the doors for better cooling

performance.

The manufacturer does not accept responsibility for any damages that may arise due to non-

observation of these instructions.

• Do not use the unit if it is damaged. If you are in any doubt, consult an engineer.

• Connection and installation of your unit are to be carried out in strict compliance with

the relative instructions in this user manual.

• Make sure there is a suitable power outlet with proper grounding to power the chiller.

• For safety, the unit must be properly earthed in accordance with specifications.

• Always remember to unplug the unit before cleaning. Never unplug this unit by pulling

on the power cable. Always grip plug firmly and pull straight out from the socket.

• All electrical repairs must be carried out by a qualified engineer. Inadequate repairs may

be dangerous.

• Do not damage any parts of the chiller which carry refrigerant by piercing, perforating,

crushing, twisting or scraping. If refrigerant comes into contact with the eyes it may

cause serious eye injury.

• Do not obstruct or cover the ventilation grille.

• Do not allow children to play with the unit, or to sit on it or hang onto the door.

• This unit is not intended for use by persons (including children) with reduced physical,

sensory or mental capabil ities, or lack of experience and knowledge, unless they have

been given supervision or instruction concerning use of the unit by a person responsible

for their safety.

BEFORE USING FOR THE FIRST TIME

IMPORTANT: Before switching the unit on, we recommend you allow it to stand

upright for 8 hours. Failure to do this may result in damage to the unit.

• Remove the wooden pallet and the packing.

• To ensure correct operation, it is important that the unit is level. The cabinet may be

levelled by turning either or both of the adjustable feet in the front corners. Use a spirit

level to check.

• Before operation, we recommend that the cabinet is cleaned for reasons of hygiene and

to remove any residue left from manufacture.

• For good circulation, vents must not be blocked. Keep a minimum of 100mm of clear

space around the chiller. Your unit should be placed on flat and firm surface for quieter

operation. Failure to do so may cause loss of performance.

• Do not expose the unit to direct sunlight or a heat source such as ovens, radiators,

heaters, etc. Failure to do so may cause loss of performance.

• Do not under any circumstances place heated food or beverages in your chiller.

• Do not open the door more often than necessary to lessen the escape of cold air.

• For better air circulation, do not overfill the unit.

• Adjust the thermostat according to the amount of product and the ambient

temperature.

CSS1H-SD-SS-NL-HU / Version 11-2022 Page 4 CSS1H-SD-SS-NL-HU / Version 11-2022 Page 5

FSS2H-SD-SS-NL-HU

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husky FSS2H Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info