Bedienungsanleitung Husky FSS2H (Seite 13 von 16) (Englisch, Holländisch)

809496

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Standard Range and Solid Door Range C1, C2, & C3Additional model-specific instructions for

CSS1 & FSS2

• These instructions should be read in conjunction with the general operating instructions on pp6&7.

Operating Instructions

TO OPERATE THE ELECTRONIC THERMOSTAT

The thermostat has been pre-set, and in most cases it is not necessary to adjust the settings.

When the unit is operating normally, the display will show the current temperature.

To display the set temperature press the button. Press the button again to return to

normal operation.

To set a new temperature, press . The display will flash and the current set temperature

will be displayed. Press the button to increase the set temperature, or press the

button to decrease the set temperature. Press the button to save the new setting. The

display will flash with the new value and then revert to display the cabinet temperature.

Please note:

1. When the chiller is connected to the mains for the first time there will be a short delay

before cooling starts. During this time the Refrigeration Light will flash. After the short

delay, cooling will begin and the Refrigeration Light will be illuminated. When the chiller

reaches the set temperature, the Refrigeration Light will be off.

2. If you do not press any button, after six seconds the controller will return to its normal

display.

DEFROSTING

The unit defrosts automatically at preset intervals. If however the door is opened too often, or

if the unit if in a location with high humidity, or if the contents are changed more frequently, it

may be necessary to defrost the unit manually. To start or stop manual defrosting, press the

button for six seconds. The Defrosting Light will be illuminated. Melt water runs to a

container placed in the compressor compartment and evaporates. After defrosting is complete,

the unit will return to normal operation.

FAST FREEZE (FSS2H ONLY)

To start quick freezing: Press “Up Arrow” for 3 seconds to start the quick-freezing function. The

corresponding LED will light. The compressor will continue to run until the temperature is

reached to the one set.

DOOR OPEN ALARM

If the door remains open for 1min or longer an alarm will be activated. The will show dr and the

room temperature alternately. A buzzer will also sound to indicate the door opening , press any

button to mute the buzzer.

REVERSIBLE DOOR

As standard both CSS1 and FSS2 models are supplied with the door hinged on the right-hand

side, opening from the left hand side. Should you wish to change the opening direction follow

the steps as follows:

1. Unplug the cabinet from the mains.

2. Remove the three screws located at the back of the lid.

3. Pull the lid forward to release.

4. Remove the three screws for the top hinge.

5. Lift the door off the bottom hinge.

6. Move the black stopper on the door over to the right-hand side.

7. Remove the two screws underneath the cabinet to release the Kick Plate.

8. Remove the lower pin to release it and move to the other side.

9. REPEAT Steps 1-7 in reverse to refit door on opposite side.

8 CSS1H-SD-SS-NL-HU / Version 11-2022 Page 9

FSS2H-SD-SS-NL-HU

CSS1H-SD-SS-NL-HU / Version 11-2022 Page

Notes

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husky FSS2H Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info