Bedienungsanleitung Husqvarna 129R (Seite 11 von 332) (Alle Sprachen)

734089

Zoom out

Zoom in

Vorherige Seite

1/332

Nächste Seite

To install a blade guard, grass blade

and grass cutter

CAUTION:

Only use the approved guard for

the blades. See

1. Attach the blade guard/cutting attachment guard (A)

onto the shaft (Picture 28) and tighten with the bolt.

2. Install the drive disc (B) on the output shaft.

3. Turn the output shaft until one of the holes in the

drive disc aligns with the related hole in the gear

housing.

4. Put the locking pin (C) in the hole to lock the shaft.

5. Put the blade (D), support cup (E) and support

flange (F) on the output shaft.

6. Install the nut (G). Torque the nut to 35-50 Nm

(26-36 ft/lb). Hold the shaft of the wrench near the

blade guard as much as possible. To tighten the nut,

you must turn the wrench in the opposite direction of

rotation.

Note:

Left hand thread.

To install blades and trimmer heads

WARNING:

Only use the approved guard for

the blades. See

. A defective guard can

cause injury.

WARNING:

If you operate the product with a

grass blade, first install the correct

handlebar, blade guard and harness .

WARNING:

If you do not install the the

blades correctly (Picture 27), it can cause

injury.

1. Make sure that the lifted section on the drive disc/

support flange engages correctly in the center hole

of the blades.

2. Install the blades.

To assemble the cutting attachment

To attach the cutting attachment guard and the trimmer

head (straight shaft)

1. Attach the cutting attachment guard (A) to the shaft

with the bolt (L) (Picture 29). Make sure to use the

correct cutting attachment guard and the correct

trimmer head.

2. Attach the drive disc (B) to the output shaft.

3. Turn the output shaft until the hole in the drive disc

aligns with the hole in the gear housing.

4. Put a small screwdriver (C) in the hole to lock the

shaft (Picture 29).

5. Turn the trimmer head (H) (Picture 30)

counterclockwise to tighten the trimmer head to the

gearbox. (Left hand threads.)

OPERATION

WARNING:

Read and understand the safety

chapter before you operate the product.

Fuel

To use fuel

CAUTION:

This product has a two-cycle

engine. Use a mixture of gasoline and two-

cycle engine oil. Make sure to use the

correct quantity of oil in the mixture.

Incorrect ratio of gasoline and oil can cause

damage to the engine.

Gasoline

CAUTION:

Do not use gasoline with an

octane number less than 90 RON (87 AKI).

This can cause damage to the product.

CAUTION:

Do not use gasoline with more

than 10% ethanol concentration (E10). This

can cause damage to the product.

• Always use new unleaded gasoline with a minimum

octane number of 90 RON (87 AKI) and with less

than 10% ethanol concentration (E10).

• Use gasoline with a higher octane number if you

frequently use the product at continuously high

engine speed.

Two-cycle engine oil

• Use only high quality two-cycle engine oil. Use only

an air cooled engine oil.

• Do not use other types of oil.

• Mixture ratio 50:1 (2%)

Gasoline Oil

1 U.S. Gal. 77 ml (2,6 oz)

1 UK Gal. 95 ml (3,2 oz)

191 - 002 -

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna 129R Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info