Bedienungsanleitung Husqvarna Automower 450X NERA - 2023 (Seite 37 von 48) (Englisch)

819081

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

7.4 LED indicator of the charging station for boundary wire installation

The LED indicator of the charging station is green when the installation is correct. If the LED indicator of the charging

station is not green, follow the troubleshooting table below.

Speak to your local Husqvarna representative or go to www.husqvarna.com for more information.

LED indicator Cause Action

Constant green The signals of the charging station are good. No action is necessary.

Flashes green The signals of the charging station are good

and

ECO mode

is enabled.

No action is necessary.

Flashes blue The boundary wire is not connected to the

charging station.

Connect the boundary wire to the charging

station.

The boundary wire is damaged. Replace the damaged section of the boun-

dary wire with new boundary wire.

Flashes red Interference in the antenna of the charging

station.

Speak to your local Husqvarna representa-

tive.

Constant red Error in the circuit board or incorrect power

supply in the charging station.

The error must be corrected by an authorized

service technician. Speak to your local Husq-

varna representative.

7.5 Symptoms

If the product does not operate as usual, follow the symptoms table below. Speak to your Husqvarna customer

service if you cannot find the cause for the fault.

Symptoms Cause Action

The product has diffi-

culty docking.

The guide wire is not put straight in a line

and correct distance from the charging sta-

tion.

Do a check of the installation of the charging

station. Refer to

To install the charging sta-

tion on page 17

The guide wire is not put in the slot in the

charging station plate.

Make sure that the guide wire is put straight

in a line and put in the slot in the charging

station plate. Refer to

To install the guide

wire on page 18

The charging station is not on a level sur-

face.

Put the charging station on a level surface.

Refer to

To examine where to put the charg-

ing station on page 11

The product operates

at the wrong time

The time or the date in the product is not

correct.

Set the time or date. Refer to

Time & date on

page 23

The start and stop times for operating are

incorrect.

Change the

Schedule

settings. Refer to

Schedule on page 20

The product vibrates. The cutting system is not in balance because

of damaged blades.

Examine the blades and screws and replace

them if necessary. Refer to

Replacement of

the blades on page 29

The cutting system is not in balance because

of too many blades in the same position.

Do a check that only one blade is attached at

each screw.

Different thickness of blades are installed on

the product.

Do a check if the blades are of different thick-

ness and replace if necessary.

2071 - 001 - 29.03.2023 Troubleshooting - 37

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna Automower 450X NERA - 2023 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Husqvarna Automower 450X NERA - 2023

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info