Bedienungsanleitung Husqvarna LC 347iVX (Seite 18 von 576) (Alle Sprachen)

733923

Zoom out

Zoom in

Vorherige Seite

1/576

Nächste Seite

To use the SavE function

The product has a battery saving function (SavE) that

gives longer operation time.

1. Push the SavE button (A) to start the function. The

SavE symbol (B) on the display comes on.

2. Push the SavE button again to stop the function. The

SavE symbol (B) on the display goes out. (Fig. 41)

The SavE function stops automatically if the ground

conditions make it necessary to have a higher output.

The SavE function starts automatically again when the

ground conditions let it.

High load function

When the product cuts long or wet grass, the motor

automatically increases rpm. The motor goes back to

standard mode when high load is not necessary.

To stop the product

The product stops automatically if you do not operate it

for 10 minutes. Always turn the safety key to 0 before

you let the product out of view.

1. Release the motor brake handle to stop the motor.

(Fig. 23)

2. Push the ON/OFF button on the control panel. All

LED lights and symbols on the display go out. (Fig.

42)

3. Open the battery lid and turn the safety key to 0.

(Fig. 43)

4. To remove the battery, push the 2 release buttons

and pull out the battery. (Fig. 44)

5. Charge the battery if it is weak. For more

information, refer to

To charge the battery on page

To get a good result

• Always use a sharp blade. A blunt blade gives an

irregular result and the cut surface of the grass

becomes yellow. A sharp blade also uses less

energy than a blunt blade.

• Do not cut more than ⅓ of the length of the grass.

Cut first with the cutting height set high. Examine the

result and lower the cutting height to an applicable

level. If the grass is very long, drive slowly and cut 2

times if necessary.

• Cut in different directions each time to prevent

stripes in the lawn.

To cut grass without a grass catcher

or mulch plug attached

• Lift up the rear cover and remove the grass catcher.

• If a mulch plug and a mulch blade are attached,

remove them.

• Close the rear cover before you operate the product.

When you operate the product, the cut grass discharges

below the rear cover.

Maintenance

Introduction

WARNING: Before you do maintenance,

you must read and understand the safety

chapter.

For all servicing and repair work on the product, special

training is necessary. We guarantee the availability of

professional repairs and servicing. If your dealer is not a

service agent, speak to them for information about the

nearest service agent.

Maintenance schedule

The maintenance intervals are calculated from daily use

of the product. The intervals change if the product is not

used daily.

For maintenance identified with * see instructions in

Safety instructions for operation on page 12

Each

use

Monthly

Each

season

Do a general inspection X

Clean the product X

Do a check of the start inhibitor * X

Make sure that the safety devices on the product are not defective * X

Examine the cutting equipment X

Examine the cutting cover * X

18 890 - 002 - 21.12.2018

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna LC 347iVX Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info