Bedienungsanleitung Husqvarna LC 347iVX (Seite 19 von 576) (Alle Sprachen)

733923

Zoom out

Zoom in

Vorherige Seite

1/576

Nächste Seite

Each

use

Monthly

Each

season

Do a check of the motor brake handle * X

Make sure that the ON/OFF button operates correctly and is not defective X

Examine the battery for damage X

Do a check of the battery charge X

Make sure that the release buttons on the battery operates correctly and that the

battery locks into the product

Examine the battery charger for damage and make sure that it operates correct-

ly.

Examine the connections between the battery and the product. Also examine the

connection between the battery and the battery charger.

To do a general inspection

• Make sure that the nuts and screws on the product

are tightened.

• Make sure that the cables on the product are not in a

position where they can get damaged.

To clean the product

• Clean plastic parts with a clean and dry cloth.

• Do not use water to clean the product. Water can

enter the battery or the motor and cause short circuit

or damage to the product.

• Do not use a high pressure washer to clean the

product.

• Do not flush water directly on the motor.

• Use a brush to remove leaves, grass and dirt.

To clean the battery and the battery

charger

CAUTION: Do not clean the battery or the

battery charger with water.

• Make sure that the battery and the battery charger

are clean and dry before you put the battery into the

battery charger.

• Clean the battery terminals with compressed air or

use a soft and dry cloth.

• Clean the surfaces of the battery and the battery

charger with a soft and dry cloth.

To examine the cutting equipment

WARNING:

To prevent accidental start, turn

the safety key to 0, remove the battery and

wait a minimum 5 seconds.

WARNING: Use protective gloves when you

do maintenance on the cutting equipment.

The blade is very sharp and cuts can easily

occur.

1. Examine the cutting equipment for damage or

cracks. Always replace a damaged cutting

equipment.

2. Look at the blade to see if it is damaged or blunt.

Note: It is necessary to balance the blade after it is

sharpened. Let a service center sharpen, replace and

balance the blade. If you hit an obstacle that causes the

product to stop, replace the damaged blade. Let the

service center estimate if the blade can be sharpened or

must be replaced.

To remove and replace the blade

1. Lock the blade with a block of wood. (Fig. 45)

2. Remove the blade bolt.

3. Remove the blade.

4. Examine the blade support and blade bolt to see if

there are damages.

5. Examine the motor shaft to make sure that it is not

bent.

6. When you attach the new blade, point the angled

ends of the blade in the direction of the cutting cover.

(Fig. 46)

7. Make sure that the blade is aligned with the center of

the motor shaft.

8. Lock the blade with a block of wood. Attach the

spring washer and tighten the bolt and washer with a

torque of 23–28 Nm. (Fig. 47)

9. Pull the blade around by hand and make sure that it

turns freely.

890 - 002 - 21.12.2018

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna LC 347iVX Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info