Bedienungsanleitung Husqvarna LC 551iV (Seite 23 von 604) (Alle Sprachen)

733939

Zoom out

Zoom in

Vorherige Seite

1/604

Nächste Seite

Each use Monthly

Each

season

Check the grass catcher for wear or deterioration X

Examine the cutting equipment X

Examine the cutting cover * X

Do a check of the motor brake handle * X

Make sure that the ON/OFF button operates correctly and is not defective X

Examine the battery for damage X

Do a check of the battery charge X

Make sure that the release buttons on the battery operates correctly and that the

battery locks into the product

Clean the air intakes. Make sure that the air intakes does not have grass or dirt

on them

Examine the battery charger for damage and make sure that it operates correctly X

Examine the connections between the battery and the product. Also examine the

connection between the battery and the battery charger

To do a general inspection

• Make sure that the nuts and screws on the product

are tightened.

• Make sure that the cables on the product are not in a

position where they can get damaged.

To replace the blade

1. Lock the blade with a block of wood. (Fig. 61)

2. Remove the blade bolt, the spring washer and the

blade. (Fig. 62)

3. Examine the blade support and blade bolt for

damages.

a) If you replace the blade or the blade support,

also replace the blade bolt, the spring washer

and the friction washer.

4. Examine the motor shaft to make sure that it is not

bent.

5. When you attach the new blade, make sure that the

bent ends point in the direction of the cutting cover.

(Fig. 63)

6. Put the friction washer and the blade against the

blade support. (Fig. 64)

7. Make sure that the blade aligns with the center of the

motor shaft. (Fig. 65)

8. Lock the blade with a block of wood. (Fig. 66)

9. Attach the spring washer and tighten the bolt with a

torque of 65-75 Nm. (Fig. 67)

10. Pull the blade around by hand and make sure that it

turns freely.

WARNING: Use protective gloves. The

blade is very sharp and cuts can easily

occur.

11. Start the product to do a test of the blade. If the

blade is not correctly attached, there is vibration in

the product or the cutting result is unsatisfactory.

To clean the product

• Clean plastic parts with a clean and dry cloth.

• Do not use water to clean the product. Water can

enter the battery or the motor and cause short circuit

or damage to the product.

• Do not use a high pressure washer to clean the

product.

• Do not flush water directly on the motor.

• Use a brush to remove leaves, grass and dirt.

To clean the battery and the battery

charger

CAUTION: Do not clean the battery or the

battery charger with water.

• Make sure that the battery and the battery charger

are clean and dry before you put the battery into the

battery charger.

• Clean the battery terminals with compressed air or

use a soft and dry cloth.

• Clean the surfaces of the battery and the battery

charger with a soft and dry cloth.

1336 - 003 - 17.12.2019

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna LC 551iV Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info