Bedienungsanleitung Husqvarna TRIBUTE 140C (Seite 18 von 48) (Englisch)

518172

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

8 9 10 11

1514 16

1817 19

18 – Operating the ma ine

FUNCTION BUTTONS ON THE TOUCH PANEL

8. Alternate View

When you select a satin stitch the length and width settings

will be shown on the GraphicDisplay. By pressing the

Alternate View button the density setting will be shown

instead of the length setting.

9. Stitch Length/Density

When you select a stitch, your machine automatically

sets the best stitch length. The stitch length is visible on

the GraphicDisplay. You can change the stitch length by

pressing the + or – button.

If you have selected a buttonhole the GraphicDisplay will

show the density setting instead of the stitch length setting.

You will now be able to change the density setting by

pressing the + and – buttons.

If you press the Alternate View button the GraphicDisplay

will show the density setting for satin stitches. Use the +

and – buttons to change the setting.

10. Stitch Width/Needle position

The stitch width is set in the same manner as the stitch

length. The preset width is visible on the GraphicDisplay.

The width can be adjusted between 0 and 7 mm. Some

stitches have a limited stitch width.

If a straight stitch is selected, the + and – buttons are used

to move the needle to the left or right in 29 positions.

11. Clear

Press this button to delete a single stitch or all stitches in

a stitch program. Or use it to delete your saved stitches

and stitch programs in the My Stitches Menu. This button

is also used to activate tapering for Decorative Tapering

Stitches.

12. Stitch Selection Buttons

By pressing any of the 0 to 9 buttons you select the stitch

illustrated on that button immediately.

By pressing two digits in quick succession you will be able to

select a stitch from 10 and up from the selected stitch menu.

If the stitch number does not exist in the selected stitch

menu you will hear a beep and the À rst entered digit will be

selected as a stitch.

13. Navigator Arrow Buttons

Make your selections with the arrow buttons and conÀ rm

your selections or changes with the OK button.

Use the left/right arrow buttons to select stitches step by

step in numerical order within the selected stitch menu.

The arrow buttons are also used when programming to

select stitches within the program or to select letters to

insert in the program.

The up and down arrow buttons are also used to set the

size of a buttonhole and to set the number of stitches

when sewing on a button.

14. Stitch Menu

Press this button to select a stitch from any of the stitch

menus shown on the GraphicDisplay.

15. Font Menu

Press this button to open the Font Menu on the

GraphicDisplay to select a font.

16. Shift to upper-case, lower-case or numbers

Press this button to shift to lower or upper-case or numbers

when programming letters.

17. Save to My Stitches

This button opens the menu where you can save your own

personal stitches or stitch programs. Press the button again

to exit the My Stitches mode.

18. Program Mode

Press this button to open the mode for programming. Press

the button again to exit the program mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna TRIBUTE 140C Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Husqvarna TRIBUTE 140C

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info