Bedienungsanleitung Husqvarna WDC 225 (Seite 13 von 368) (Alle Sprachen)

734150

Zoom out

Zoom in

Vorherige Seite

1/368

Nächste Seite

To install the tube holder

1. Move the tube holder vertically on the extension

tube.

2. Use a screwdriver to install the tube holder on

correct height of the extension tube. (Fig. 19)

3. Park the extension tube at the holders on the rear of

the product. (Fig. 20)

Operation

Introduction

WARNING: Before you operate the product,

you must read and understand the safety

chapter.

To start the product

Before the product is used, make sure that the

frequency and voltage shown on the rating plate is the

same as the mains voltage.

1. Make sure that the main switch is in position "0".

(Fig. 10)

2. Do a check that correct filters are in position in the

product.

3. Put the hose into the vacuum inlet at the front of the

product. Push the hose forward until it is installed

tightly in position in the vacuum inlet. (Fig. 16)

4. Connect the two extension tubes with the handle.

Twist the extension tubes to make sure that they are

correctly in position.

5. Attach a nozzle to the extension tube. Select the

nozzle after the type of material that is to be cleaned.

6. Connect the plug into the mains.

7. Put the main switch into position "I" to start the

product. (Fig. 17)

To stop the product

1. Put the main switch into position "0" to stop the

product.

2. Disconnect the plug from the mains. (Fig. 10)

To use the blow function

1. Put the hose in the opening on the rear of the

product. (Fig. 21)

2. Connect the plug into the mains.

3. Put the main switch to the "I" position. (Fig. 17)

4. Adjust the blow power on the handle or by the main

switch*. *Only on some models. (Fig. 22)

To use the power tool socket*

*Only on some models.

CAUTION:

Follow the operating instructions

and safety instructions for appliances

connected to the power tool socket.

Note: The maximum power consumption of the

connected tool is told in section

Technical data on page

1. Make sure that the switch on the power tool is in

position "0". (Fig. 23)

2. Disconnect the handle from the hose. Press the

hatches on the hose end (A) and pull out the handle

(B). (Fig. 24)

3. Connect the power tool adaptor. (Fig. 25)

4. Adjust the suction power on the power tool adaptor

or by the main switch*. *Only on some models. (Fig.

26)

5. Connect the hose to the vacuum inlet of the product

and to the power tool. Connect the cable of the

power tool to the electrical connection of the product.

(Fig. 27)

6. Make sure that the switch on the power tool is in

position "0". (Fig. 23)

7. Turn the main switch on the product to the power

tool position (A).

8. Put the switch of the power tool to "I" (B). (Fig. 28)

Note: You can start and stop the product with the

main switch on the product (A) or on the power tool

(B).

To clean liquid

Note: The product has a float system that stops the

airflow through the product at the maximum liquid level.

CAUTION: Do not clean liquid without the

float system in position.

1. Make sure that the filter and the filter tension (the

float system) is in position, see

To replace the filter

on page 15

. Remove the filter bag if it is installed.

2. Use the floor nozzle to clean liquid.

3. At the maximum liquid level, a noticeable change of

the motor sound is heard. The suction power

decreases.

4. Stop the product, see

To stop the product on page

5. Empty the dirt container, see

To empty the dirt

container after liquid pick up on page 14

562 - 004 - 20.03.2019

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna WDC 225 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info