Bedienungsanleitung Husqvarna Z560X (Seite 26 von 280) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

733969

Zoom out

Zoom in

Vorherige Seite

1/280

Nächste Seite

Caster Wheels

Check every 200 hours. Check that wheels rotate

freely.

To replace, remove nut and caster bolt. Pull the

wheel out of the fork. Install in reverse order.

Tighten caster bolt. Torque to 50 ft-lbs (67.8 Nm).

NOTE: Tire must rotate freely but axle spacers

must not. If wheels do not rotate freely take the

unit to the dealer for service.

Cleaning

CAUTION! Always wear eye

protection when cleaning and

washing.

Regular cleaning and washing, especially under

the mower deck, will increase the machine’s life-

span. Make it a habit to clean the machine directly

after use (after it is cooled), before the dirt sticks.

Do not spray water on the top of the mower deck.

Use compressed air to clean the top side of

mower deck. Regularly clean deck and underside

of the deck with normal water pressure. Do not

use a high pressure washer or steam cleaner.

Avoid spraying engine and electrical components

with water.

Do not rinse hot surfaces with cold water. Let unit

cool before washing.

Hardware

Check daily. Inspect the entire machine for loose

or missing hardware.

Anti-scalp Rollers

Anti-scalp rollers keep the deck in the proper

position to help prevent scalping in most terrain

conditions. Do not adjust the rollers to support the

deck.

IMPORTANT INFORMATION Adjust anti-

scalp rollers with the mower on a at level

surface. To avoid deck damage, the anti-scalp

rollers must not be adjusted to support the

deck.

Anti-scalp rollers can be set in three positions.

• Upper 38 mm - 64 mm grass

• Middle 64 mm -102 mm grass

• Lower 102 mm - 127 mm grass

The rollers must be approximately 6.35 mm from

ground. Do not adjust the rollers to support the

deck.

Safety System

The machine is equipped with a safety system

that prevents starting or driving under the

following conditions.

The engine can only be started when:

• the mower deck is disengaged.

• the steering / park brake controls are in the

outer, locked neutral position, making sure

of full parking brake engagement for a safe

startup.

NOTE: If the steering / park brake controls are not

holding in the full outboard position, the tension

can be adjusted. (See Park Brake in this section).

Make daily inspections to make sure that the

safety system works by trying to start the engine

when one of the conditions is not met. Change

the conditions and try again.

Make sure the engine stops when the park brake

is not engaged and the operator leaves the

seated position.

Make sure the engine stops if the mower blades

are engaged and the driver leaves the seated

position.

IMPORTANT INFORMATION To drive, the

driver must sit in the seat and the steering /

park brake controls must be moved into the

engaged (outer) position. Otherwise the engine

will stop.

MAINTENANCE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna Z560X Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info