44
Chimney requirem○ents
The chimney must be of a sufficient height to enable an adequate draft and to prevent smoke problems.
Nominal draft: approx. 12 Pa.
The chimney must have a minimum opening equivalent to Ø 150 mm. The chimney opening should
always be at least the size of the outlet socket of the stove. The chimney must have an easily accessible
soot door.
Changing the smoke outlet from top outlet to rear outlet (Drawing B)
1. Removing sides. Lift one side about 10 mm and pull it away from the stove so that it disengages from
the guide pins on the bottom plate of the stove. Repeat on the other side.
2. Removing the top plate (1). Remove the four screws (Torx Bit no. 30 or M6 nut) beneath the top plate,
two on each side, and lift the top plate off.
3. Removing the rear plate (2). Lift the rear plate and pull it away from the stove so that it disengages
from the guide pins on the bottom plate of the stove. There is a cut-out in the rear plate for the smoke
outlet. Break off the plate within this cut-out to make a hole in the rear plate so there is room for the
smoke outlet.
4. Removing the cover plate (3). Remove the cover plate on the back of the stove by removing the three
screws (Torx Bit no. 30).
5. Removing the flue ring (4). Remove the three screws. Lift the flue ring off the top of the stove.
6. Installing the cover plate (3). Mount the cover plate on the top of the combustion chamber using the
three screws (Torx bit no. 30).
7. Installing the flue ring (4). Insert the flue ring into the smoke outlet hole in the rear of the stove and
secure it with the three screws.
8. Installing the rear plate (2). Place the rear plate on the guide pins at the back of the bottom plate of
the stove; then press it in towards the stove. Lift the rear plate and press it lightly inwards until it
engages with the guide pins.
9. Installing the top plate of the stove (1). Place the top plate on the fittings and secure it with the four
screws, two on each side.
10. Installing sides. Put the sides on the guide pins in the bottom plate of the stove and press them in towards
the stove. Lift the sides and press them lightly inwards until they engage with the guide pins.
Installing soapstone in the heat compartment (Drawing I)
1. Lift one of the stove sides (1) about 10 mm and pull it away from the stove so that it disengages from
the guide pins on the bottom plate of the stove. Repeat on the other side.
2. Remove the four screws (2) (Torx Bit no. 30) beneath the top plate, two on each side, and lift the top
plate (3) off.
3. Remove the smoke ring (4) at the top of the stove by loosening the three screws (5) (Torx Bit no. 30).
4. Remove the two pins (6) - one on each side - that lock the top plate of the heat storage compartment.
Lift the top plate (7) slightly at the front and pull it away from the guide pins (8) found at the rear.
5. Remove the smoke pipe (9) from the heat storage compartment.
6. Loosen the two screws (10) on each side of the heat storage compartment that support the front
plate of the heat storage compartment (11), and remove the front plate.
7. Place soapstone slabs (12) in the heat storage compartment making sure that the hole in every slab
is right above the smoke ring.
8. Reattach the front plate of the heat storage compartment (11).
9. Lead the smoke pipe (9) through the hole in the soapstone slabs and down into the smoke ring at the
bottom of the heat storage compartment.
10. Reposition the top plate of the heat storage compartment (7) in the guide pins (8) at the rear; once
the top plate is correctly in place, lock it with the two pins (6).
11 Mount the smoke ring (4) on top of the top plate of the heat storage compartment using the three
screws. (5).
