Bedienungsanleitung Hwam 4620 (Seite 42 von 48) (Englisch, Dänisch, Schwedisch, Norwegisch)

613741

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Storage of wood

A water content of a maximum of 18% is achieved by storing the wood for a minimum of one year,

preferably two years, outdoors under a lean-to. Wood stored indoors has a tendency to become too

dry and combust too quickly. However, it might be advantageous to store fuel for lighting a re indoors

for a few days prior to use.

Recommended dimensions

The dimensions of the fuel are important to good combustion. The dimensions should be as follows:

Fuel type Length in cm Diameter in cm

Wood for kindling a re (nely chopped) 30-45 2-5

Chopped wood 30-45 7-9

Special re lighting guide for stoves with soapstone or sandstone cladding

Soapstone and sandstone are natural products which need to adjust to temperature changes. We

recommend following the procedure below:

1. First stoking

Turn the regulator (drawing E, 1) clockwise to maximum. Place two pieces of wood (5-8 cm in diameter)

horizontally in the bottom of the combustion compartment (corresponding to 1-1,5 kg). Place 6-10

pieces of kindling randomly on top. Place four relighters between the top layer of kindling. Light up the

re-lighters and close the stove door. If condensation forms on the glass, keep the door ajar for a little

while and close again. When the re has gone out, open the door and leave it open while the stove cools

to room temperature.

2. Second stoking

Turn the regulator (drawing E, 1) clockwise to maximum. Place two pieces of wood (5-8 cm in diameter)

horizontally in the bottom of the combustion compartment (corresponding to 1-1.5 kg). Place 6-10 pieces

of kindling randomly on top. Place four relighters between the top layer of kindling. Light up the re-lighters

and close the stove door. If condensation forms on the glass, keep the door ajar for a little while and close

again. When no more yellow ames are visible and a suitable layer of embers has built up, the stove can be

stoked again. A suitable ember layer is when the bottom of the combustion chamber is covered by embers

which are shining brightly. Place 2 pieces of new rewood (up to 1.2 kg each) with a diameter of approx.

7-9 cm in the combustion chamber. When all of the wood has caught re, turn the regulator (1) to middle

position. Allow the re to burn and let the stove cool to room temperature before stoking again.

3. Third stoking

Repeat the procedure for the second stoking, but put in more wood this time. Allow the re to burn and

let the stove cool to room temperature after the re has gone out.

Restoking

Follow the general instructions, see the sections “Lighting the stove” and “Stoking”.

Lighting the stove (drawing E)

A successful combustion process requires that the wood is lit in the right way. A cold stove and a cold

chimney challenge the combustion process. It is important to achieve a high ue gas temperature quickly.

Turn the regulator (1) clockwise to maximum. Place two pieces of wood (5-8 cm in diameter) horizontally

in the bottom of the combustion compartment (corresponding to 1-1.5 kg). Place 6-10 pieces of kindling

randomly on top. Place four relighters between the top layer of kindling. Light up the re-lighters and

close the stove door. If condensation forms on the glass, keep the door ajar for a little while and close again.

When the kindling is burning well, turn the regulator (1) to middle position. If the re goes out when

the regulator is turned, return it to maximum position again until the fuel catches re and then turn it

to middle position again. Allow the kindling to burn up completely until there are no longer any visible

ames. The stove can then be stoked again.

Important! The ash pan must not be opened during the lighting stage and must always be kept closed

when the stove is lit or the Autopilot might be damaged. Only open the door when lighting the stove,

refuelling it and cleaning it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hwam 4620 Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hwam 4620

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info