Bedienungsanleitung I-onik WS-110 (Seite 6 von 6) (Deutsch, Englisch)

521906

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

10 11

7. House Security Code Settings

Unless the factory settings of the i.onik

Alarmsystem Smart Panel have been altered, the House

Security Code will NOT need to be changed.

However, if the settings on the Smart Panel have been altered, or need to be altered to solve the pro-

blem of the Smart Panel and sensors activating intermittently (or not working at all) or interference

with other systems, then the House Security Code on all system modules (sensors and sirens), will

also need to be changed.

House Security Code Settings can be altered as follows:

• There are 4 jumpers or dip-switches on each device.

• Remove the battery compartment cover then toggle the dip switch contacts to change the House

Security Code.

• If the dip switch is up it is ON, if it is down it is OFF. Default code on the Auto Dialler is with all the

dip switches ON (up).

• To ensure the system works correctly, make sure the jumpers on the Smart Panel and all other

system modules (sensors and sirens) match exactly.

8. Maintenance

The product may be cleaned with a soft damp cloth and then wiped dry. Do not use abrasive, solvent

based or aerosol cleaners as this may damage and/or discolour the product. Do not allow water to

enter or attempt to clean inside the unit.

9. Batteries

Do not allow the batteries to corrode or leak as this may cause permanent damage to the product.

Take care to insert the batteries with the correct polarity as shown inside the battery compartments.

Do not mix new and old batteries or different types of batteries. Do not use rechargeable batteries.

At the end of their useful life the batteries should be disposed of via a suitable recycling centre. Do

not dispose of with your normal household waste. DO NOT BURN.

10. Alarm System Limitations

Even the most advanced alarm systems cannot guarantee 100 % protection against burglary or

environmental problems. All alarm systems are subject to possible compromise or failure-to-warn

for a variety of reasons.

Please note that you may encounter problems with your system if:

• The Smart Panel is not placed within hearing range of persons sleeping or remote parts of the

premises.

• The sensors are placed behind doors or other obstacles.

• Intruders gain access through unprotected points of entry (where sensors are not located).

• Intruders have the technical means of bypassing, jamming, or disconnecting all or part of the system.

• The power to the sensors is inadequate or disconnected.

• The sensors are not located in proper environmental/temperature conditions i.e. too close to a heat

source.

Note:

Inadequate maintenance is the most common cause of alarm failure; therefore, test your

system at least once per week to be sure the sensors and sirens are working properly.

Although having an alarm system may make you eligible for reduced insurance premiums,

the system is no substitute for insurance.

Jumpers for house security

code

- Smart Panel

- Each sensor

Default house code: 1: ON, 2: ON, 3: ON, 4: ON

*Jumper: ON = Plugged, OFF = Pull Out

Dip-Switches for house

security code

- Key Fob Remote

Default house code: 1: ON, 2: ON, 3: ON, 4: ON

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

I-onik WS-110 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info