12346
83
Zoom out
Zoom in
Vorherige Seite
1/116
Nächste Seite
70
8
SCANS
2001 NEW
Programmed scan/Fine programmed scan (VFO mode)
Programmed scan searches for signals between scan
edge memory channels P1 and P2. The default fre-
quencies for these memories are 0.500000 MHz and
29.99999 MHz, respectively. See p. 65 for scan edges
programming.
q Push [V/M] to select VFO mode, if necessary.
w Select the desired operating mode.
The operating mode can also be changed while scan-
ning.
e Push [TS] to select a tuning step.
The tuning step can also be changed while scanning.
r Push [MENU] to select M2.
t Push [F1 SCN] to select the scan menu.
See p. 68 for scan condition.
If the [RF/SQL] control function is set as AUTO, the
squelch is always open in SSB, CW and RTTY modes.
y Push [F1 PRO] to start the programmed scan.
The MHz and kHz decimal points blink while scanning.
u When the scan detects a signal, the scan stops,
pauses or ignores it depending on the resume, VSC
setting and the squelch condition.
i To cancel the scan, push [F1 PRO].
Rotating the tuning dial during scan also cancels scan
operation.
If the same frequencies are programmed into the
scan edge memory channel P1 and P2, pro-
grammed scan does not start.
DD
About the Fine programmed scan
During programmed scan, when a signal is received,
scan continues, but the tuning step is temporarily set to
10 Hz.
q Follow steps q to y above to start programmed
scan.
w During programmed scan, push [F3 FIN] to switch
between programmed scan and fine programmed
scan operation.
e Push [F1 PRO] to cancel the scan.
Rotating the tuning dial during scan also cancels scan
operation.
[TS]
Tuning dial
[MENU]
[V/M]
Mode keys
F 1
F
2F
3
F
4
F
5
F 1
F 2 F 3 F 4 F 5
F 1
F
2F
3
F
4
F
5
SCN
MEM
SWR
TCN
VSC
PRO
F
FIN
SPN
SET
F:±1Ok
PRO
F
FIN
SPN
SET
PROG
SCAN
Push [F1]
Push [F1] to start/cancel the scanning.
Push [F1]
F 1
F
2F
3
F
4
F
5
F 1
F
2F
3
F
4
F
5
PRO
F
FIN
SPN
SET
PROG
SCAN
PRO
F
FIN
SPN
SET
F-PROG
SCAN
Push [F3] to switch
between programmed
scan and fine pro-
grammed scan.
IC-7400.qxd 02.4.2 11:35 Page 70
83

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Icom IC-7400 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info