Bedienungsanleitung Icom IC-7400 (Seite 88 von 116) (Englisch)

12346

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

ANTENNA TUNER OPERATION

2001 NEW 2001 NEW

■ Antenna tuner operation

The internal automatic antenna tuner matches the

transceiver to the connected antenna automatically.

Once the tuner matches an antenna, the variable ca-

pacitor angles are memorized as a preset point for each

frequency range (100 kHz steps). Therefore, when you

change the frequency range, the variable capacitors are

automatically preset to the memorized point.

CAUTION: NEVER transmit with the tuner ON

when no antenna is connected. This will damage

the transceiver. Be careful of the antenna selection.

TUNER OPERATION

➥ Push [TUNER] to turn the internal antenna tuner

ON. The antenna is tuned automatically when the

antenna SWR is higher than 1.5:1.

• When the tuner is ON, the “TUNE” indicator appears.

• MANUAL TUNING

During SSB operation at low voice levels, the internal

tuner may not be tuned correctly. In such cases, man-

ual tuning is helpful.

➥ Push [TUNER] for 1 sec., to start manual tuning.

•A side tone is emitted and “TUNE” indicator blinks while

tuning.

•If the tuner cannot reduce the SWR to less than 1.5:1

after 20 sec. of tuning, the [TUNER] switch indicator

goes out.

• AUTOMATIC TUNER START (HF bands only)

If you want to deactivate the tuner under conditions

of VSWR 1.5:1 or less, use the auto tuner start func-

tion and turn the tuner OFF. This function activates

the tuner automatically when the SWR exceeds 1.5:1.

This function is turned ON in set mode. (p. 83).

• PTT TUNER START

The tuner is always tuned when the PTT is pushed

after the frequency is changed (more than 1% from

last-tuned frequency). This function removes the

“push and hold [TUNER]” operation and activates for

the ﬁrst transmission on a new frequency.

This function is turned ON in set mode. (p. 83).

• Antenna tuner of the IC-PW1

When using an external antenna tuner such as the

IC-PW1’s tuner, tune with the external antenna tuner,

while the internal tuner is turned OFF. After tuning is

completed, turn the internal tuner ON. Otherwise,

both tuners tune simultaneously and correct tuning

may not be obtained.

See the instruction manual included with each an-

tenna tuner for their respective operations.

[TUNER]

If the tuner cannot tune the antenna

Check the following and try again:

• the [ANT] connector selection.

• the antenna connection and feedline.

•the unaltered antenna SWR.

(Less than 3:1 for HF bands;

Less than 2.5:1 for 50 MHz band)

•the transmit power. (8 W for HF bands; 15 W for 50 MHz

band)

• the power source voltage/capacity.

If the tuner cannot reduce the SWR to less than 1.5:1

after checking the above, perform the following:

• repeat manual tuning several times.

• tune with a 50 Ω dummy load and re-tune the antenna.

• turn power OFF and ON.

•adjust the antenna cable length.

(This is effective for higher frequencies in some cases.)

•Some antennas, especially for low bands, have a nar-

row bandwidth. These antennas may not be tuned at the

edge of their bandwidth, therefore, tune such an an-

tenna as follows:

[Example]: Suppose you have an antenna which has an

SWR of 1.5:1 at 3.55 MHz and an SWR of 3:1 at 3.8 MHz.

q Push [TUNER] to turn the antenna tuner ON.

w Select CW mode.

e Turn OFF the break-in function. (p. 55)

r Push [TRANSMIT] to set to the transmit condition.

t Set 3.55 MHz and key down.

y Set 3.80 MHz and key down.

u Push [TRANSMIT] to return to the receive condition.

NOTES:

•The internal antenna tuner can only tune the HF and

50 MHz bands— the 144 MHz band cannot be tuned.

•NEVER transmit without an antenna properly connected

to antenna port in use.

•When 2 antennas are connected, select the antenna to

be used with [ANT].

•If the SWR is higher than about 1.5:1 when tuning above

100 kHz on an antenna’s preset point, push [TUNER] for

1 sec. to start manual tuning.

•The internal tuner may not be able to tune in AM mode. In

such cases, push [TUNER] for 1 sec. to manually tune.

IC-7400.qxd 02.4.2 11:35 Page 75

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Icom IC-7400 Seite 88

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info