12346
86
Zoom out
Zoom in
Vorherige Seite
1/116
Nächste Seite
73
8
SCANS
2001 NEW
Tone scan/DTCS code scan operation
By monitoring a signal that is being operated with a re-
peater, tone squelch or DTCS, you can determine the
tone frequency necessary to open a repeater or the
squelch.
q Push [AM/FM] to select FM mode.
w Push [MENU] several times to select M1.
e Push [F4 TONE] for 1 sec. to enter tone set mode.
r Push [F1 TON] to select the tone type to be
scanned.
•“Rptr Tone for repeater tone, TSQL Tone for
tone squelch and DTCS Code for DTCS code can be
selected.
When selecting DTCS code to be scanned, push [F5]
several times to select the DTCS code polarity.
NN : Normal polarity for both transmit and receive.
NR : Normal polarity for transmit and reverse polarity
for receive.
RN : Reverse polarity for transmit and normal polarity
for receive.
RR : Reverse polarity for both transmit and receive.
t Push [F2 SCN] to start the tone scan function.
•“Rptr Tone SCAN, TSQL Tone SCAN or
DTCS Code SCAN blinks when repeater tone scan,
tone squelch scan or DTCS code scan is operated, re-
spectively.
y When a matched tone or code is found, the scan
pauses and the tone frequency or code is set for the
selected tone as in step r.
When the tone scan or DTCS code scan is operated
in memory or call channel mode, the detected tone fre-
quency or code can be used temporarily.
To keep the detected tone frequency or code setting
for memory contents, you must over-write the memory
or call channel.
u Push [F2 SCN] to cancel the tone scan function.
Rotating the tuning dial during scan also cancels scan
operation.
F 1
F 2 F 3 F 4 F 5
F 1
F 2 F 3 F 4 F 5
F 1
F 2 F 3 F 4 F 5
F 1
F 2 F 3 F 4 F 5
F 1
F 2 F 3 F 4 F 5
AGC
DUP
CMP
TON
SCP
TON
SCN
88.5Hz
Rptr
Tone
TON
SCN
88.5Hz
Rptr
Tone
SCAN
Push [F4] for 1 sec.
Push [F1] several times to select tone type.
Repeater tone scan
Tone squelch tone scan
DTCS code scan
TON
SCN
88.5Hz
TSQL
Tone
SCAN
TON
SCN
O23-NN
DTCS
Code
SCAN
Push [F2] to start/cancel the scan.
Push [F2] to start/cancel the scan.
Push [F2] to start/cancel the scan.
Push [F1] several times to select polarity.
IC-7400.qxd 02.4.2 11:35 Page 73
86

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Icom IC-7400 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info