Bedienungsanleitung Icom IC-7600 (Seite 16 von 180) (Englisch)

670162

Zoom out

Zoom in

Vorherige Seite

1/180

Nächste Seite

$6 MEMORY UP/DOWN SWITCHES [∫]/[√] (p. 99)

➥

Push to select the desired memory channel.

• Memory channels can be selected both in VFO and

memory modes.

➥

Push to select the desired memory channel di-

rectly after pushing [F-INP ENT] and a memory

channel number.

$7 MEMOR

Y WRITE SWITCH [MW] (p. 101)

Stores the selected readout frequency and operat-

ing mode into the displayed memory channel when

pushed and held for 1 sec.

• This function is available both in VFO and memory

modes.

$8 MEMO PAD-WRITE SWITCH [MP-W] (p. 104)

Programs the displayed readout frequency and op-

ating mode into a memo pad.

• The 5 most recent entries remain in memo pads.

• The memo pad capacity can be expanded from 5 to 10

in others set mode. (p. 132)

$9 MEMO PAD-READ SWITCH [MP-R] (p. 104)

Each push calls up a frequency and operating

mode in a memo pad. The 5 (or 10) most recently

programmed frequencies and operating modes

can be recalled, starting from the most recent.

• The memo pad capacity can be expanded from 5 to 10

in others set mode. (p. 132)

%0 VFO/MEMORY SWITCH [VFO/MEMO]

➥ Switches the selected readout operating mode

between the VFO and memory when pushed.

(pgs. 26, 99)

➥ Transfers the memory contents to VFO when

pushed and held for 1 sec. (p. 102)

%1 Q

UICK TUNING SWITCH [TS]

➥ Turns the quick tuning step ON and OFF. (p. 29)

• While the quick tuning indicator, “Z,” is displayed

above the frequency indication, the frequency can

be changed in programmed kHz steps.

• 0.1, 1, 5, 9, 10, 12.5, 20 and 25 kHz steps are avail

le for each operating mode independently.

➥ When the quick tuning step is ON, push and hold

for 1 sec. to enter quick tuning step set mode.

(p. 29)

➥ When the quick tuning step is OFF, push and

hold for 1 sec. to turn the 1 Hz tuning step ON

and OFF. (p. 30)

AUDIO PEAK FILTER/TWIN PEAK FILTER

SWITCH [APF/TPF]

During CW mode operation (p. 39)

➥ Push to turn the audio peak ﬁlter ON and OFF.

• “ ” appears when audio peak ﬁlter is in use.

➥ When the audio peak ﬁlter is ON, push and hold

for 1 sec. to select the APF passband width

from WIDE, MID and NAR or from 320, 160 and

80 Hz depending on APF type setting (SOFT or

SHARP).

During RTTY mode operation (p. 47)

➥ Push to tur

n the twin peak ﬁlter ON and OFF.

• “ ” appears when twin peak ﬁlter is in use.

• The indicator on this switch lights green when the

function is activated.

■ Front panel (continued)

TWIN

PBT

RIT/ TX

NOTCH

CW PITCH

VOICE MEMORY

BAL NR

AF RF/SQL

MIC GAIN RF POWER BK

IN DELAY KEY SPEED

TIMER

PHONES

ELEC

KEY

MIC

AUTO

TUNE

GENE F

INP

1.8 3.5

1 2

ENT

CHANGE

XFC

SPLIT

DUAL

WATCH

MAIN

SUB

M.SCOPE

VFO/MEMO

NRNB

PBT

CLR

APF/TPF

NOTCH

POWER

RIT

CLEAR

SPEECH

LOCK

FILTER

REC PLAY

EXIT

SET

SSB CW

RTTY

PSK

AM/FM

MONITOR

TRANSMIT

TUNER

HF/50MHz TRANSCEIVER

LOCKTX RX SPLIT

$7 $8 $9 %0%1

PANEL DESCRIPTION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Icom IC-7600 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info