Bedienungsanleitung Icom RS-BA1 (Seite 55 von 58) (Englisch)

670304

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

TROUBLESHOOTING

Problem: Cannot properly control the radio with the Remote Controller

Possible cause 1

ThesameCI-VaddressisbeingusedbyacontrolsoftwareotherthantheRemoteController.

Solution

Select an address other than “E0” in the CI-V Address (RS-BA1) menu in the Remote Controller’s

Connect Setting screen. However, this solution does not always solve the problem.

Possible cause 2

In the Remote Controller’s Connect Setting screen, a different model name is selected for the radio

that you attempt to control.

Solution

Select the proper model name in the Model menu in the Connect Setting screen.

NOTE:

If you could not solve the problem after trying the solutions described on the previous page and above, check

the following on the Base station side.

•IsthereanyradiothathasthesameCI-Vaddressinthesystem?

Problem: The received audio cannot be heard

The description in this part is based on the assumption that the connection to the radio has succeeded (“<<CON-

NECT>>” is displayed under the radio name).

Possible cause 1

The speaker is not turned ON, or the volume level is too low.

Solution

Turn ON the speaker, or adjust the volume level.

Possible cause 2

An earphone or other device is connected to the computer in place of the speaker.

Solution

Disconnect the device.

Possible cause 3

The appropriate audio device is not selected in the Remote Utility.

Solution

Select the appropriate audio device in the AF Output Device menu in the Connection Setting screen

(Radio Operation mode ➔ Radio List screen ➔ [Settings])

(pp.25,36)

If you connect a new USB audio device to your PC, the audio device which is selected as a default

device in your PC can be changed. If you select “Default Device” in the AF Output Device menu,

please keep that in mind.

Possible cause 4

The volume level of the audio device is set to too low on your PC.

Solution

Adjustthevolumeleveloftheaudiodevice.(pp.5to8)

Windows8.1,Windows8,Windows7andWindowsVistahavetheVolumeMixerfunctionthatcan

adjusteachapplication’saudiolevel.IfyouuseWindows7orWindowsVista,pleasecheckthatthe

Remote Utility or the control software is not muted, or set to an appropriate volume level.

Possible cause 5

Audio output is disabled in the Remote Utility.

Solution

Insert a check mark in the AF Transmission box in the Connection Setting screen (Radio Operation

mode ➔ Radio List screen ➔ [Settings]).

Possible cause 6

The volume level is too low, or the mute is turned ON in the Remote Utility.

Solution

Adjust the volume level in the Received Audio Adjustment screen (Radio Operation mode ➔ Radio

List screen ➔ [AF]).

(p.28)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Icom RS-BA1 Seite 55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info