Bedienungsanleitung iHealth BG5 (Seite 9 von 16) (Englisch)

783862

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

14 15

Control Solution

Control solution contains a known amount of glucose that

reacts with test strips and is used to ensure that your meter

and test strips are working together properly.

Material needed:

• iHealth Wireless Smart Gluco-Monitoring System (BG5)

• iHealth AGS-1000I Blood Glucose Test Strip

• Control Solution

Perform Control Solution test when:

• First receiving the meter

• Checking the meter and test strips at least once a week

• Using a new vial of test strips

• You suspect the meter or test strips are not working properly

• Your blood glucose test results are not consistent with how

you feel, or if you think the results are not accurate

• Practicing the testing process

• The meter has been dropped or damaged

Step 1: Insert the test strip to turn on the meter

Insert the test strip in the meter’s Strip Port, and wait for the

Blood Sample Symbol to appear in the meter display.

Step 2: Press the Memory Button to

turn on the control (“CTL”) mode.

When the “CTL” symbol appears, the

meter is in control ode and will not save

this test results in memory.

Performing an Ofﬂine Control Solution Test with Meter

Alone (not using iOS device)

When taking a Control Solution Test with meter alone, it is

important to set the test mode to “CTL,” so that the result

will not be mixed up with your regular test results. Control

Solution Test results will not be saved in the meter’s memory.

Please follow the instructions below.

Step 3: Press the “Memory Button” again to turn off the

“CTL” mode and switch back to the regular testing

mode.

When the “CTL” symbol disappears from the meter display,

the meter is in regular testing mode and subsequent tests

will not be treated as a control solution test.

Step 4: Apply Control Solution

• Shake the Control Solution vial before each use.

• Squeeze a drop of Control Solution and place it in the vial

cap. For better results, it is recommended that you use the

second drop of the Control Solution (discard the ﬁrst drop).

• Hold the meter and move the absorbent hole of the test

strip to catch the drop. Once the conﬁrmation window ﬁlls

completely, the meter will start counting down. Please

leave the test strip blood samples when the countdown

begins.

Note: To avoid contaminating the entire vial of Control

Solution, do not directly apply Control Solution onto a strip.

Step 2: Tap the “CTL” button to switch to Control (“CTL”)

mode

Step 1: Launch the App

I Performing an Online Control Solution Test (with iOS

device)

Step 5: Read and Compare the Results

After counting down to “1” the Control

Solution test result will appear on the

meter display.

The result of the Control Solution test

should be within the range printed on the

test strip vial label. If the test result falls

outside the speciﬁed range, repeat the test, carefully

following the steps above.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

iHealth BG5 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von iHealth BG5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info