ESP 26
una de las tres letr
botón
ENGLISH
8
• Switch on the appliance by pressing the ON/OFF button.
• Switch of f the appliance by pressing the ON/OFF button.
• Hold down button for 5 seconds, until you hear a b eep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
������
Press button to select the desired hardness le vel (see
W A TER HARDNESS T ABLE).
• Switch of f the appliance by pressing the ON/OFF button.
Setting is complete!
W ater Hardness T able
Level °dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 1 1 1 1 - 20
3 A verage 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 V ery hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly , so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-W ash” program alone is NOT ������
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
�������������������������������� s .
��������������������������������
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE W A TER HARDNESS
T o allow the water softener to work in a perfect way , it is essential
that the water hardness setting is based on the actual water hard -
ness in your house. This information can be obtained from your local
water supplier . The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DR YING easier . The rinse aid dispenser A
should be lled when the RINSE AID REFILL indicator light
in the control panel is lit.
1. Open the dispenser B by pressing and pulling up the tab on
the lid.
2. Carefully introduce the rinse aid as far as the maximum
(1 10 ml) reference notch of the lling space - avoid spilling it.
If this happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the tub.
A
B
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
adjust the quantity of rinse aid used.
• Switch the dishwasher on using the ON/OFF button.
• Switch it of f using the ON/OFF button.
• Press button three times - a beep will be hear d.
• Switch it on using the ON/OFF button.
•
•
The current selection level number and rinse aid indicator light ash.
Press button to select the level of rinse aid qu antity to be
supplied.
• Switch it of f using the ON/OFF button.
Setting is complete!
If the rinse aid level is set to ZERO (ECO), no rinse aid will be
supplied. The LOW RINSE AID indicator light will not be lit if you
run out of rinse aid. A maximum of 5 levels can be set according to
the dishwasher model. The factory setting is specic to the model,
please follow instruction above to check this for your machine.
• If you see bluish streaks on the dishes, set a low number (1-2).
• If there are drops of water or limescale marks on the dishes,
set a high number (3-4).
FILLING THE DETERGENT DISPENSER
������������������������������
dishwashers.
T o achieve the best washing and drying results, the combined
useof detergent, rinse aid liquid and rened salt is required.
W e recommend using detergents that do not contain phosphates
or chlorine, as these products are harmful to the environment.
Good washing results also depend on the correct amount of
detergent being used.
Exceeding the stated amount does not result in a more ef fective
wash and increases environmental pollution.
The amount can be adjusted to the soil level. In the case of
normally soiled items, use approximately either 35g (powder
detergent) or 35ml (liquid detergent) and additional tea spoon of
detergent directly inside the tub. If tablets are used, one tablet
will be enough.
If the crockery is only lightly soiled or if it has been rinsed with
water before being placed in the dishwasher , reduce the amount
of detergent used accordingly (minimum 25 g/ml) e.g. skip the
powder/gel putted inside the tub.
T o open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only .
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
1.
2.
When measuring out the detergent refer to the mentioned ear -
lier information to add the proper quantity . Inside the dispenser
B there are indications to help the detergent dosing.
Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
hasta que llegue
y mantenga pulsado el
ENGLISH
8
• Switch on the appliance by pressing the ON/OFF button.
• Switch of f the appliance by pressing the ON/OFF button.
• Hold down button for 5 seconds, until you hear a b eep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
������
Press button to select the desired hardness le vel (see
W A TER HARDNESS T ABLE).
• Switch of f the appliance by pressing the ON/OFF button.
Setting is complete!
W ater Hardness T able
Level °dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 1 1 1 1 - 20
3 A verage 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 V ery hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly , so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-W ash” program alone is NOT ������
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
�������������������������������� s .
��������������������������������
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE W A TER HARDNESS
T o allow the water softener to work in a perfect way , it is essential
that the water hardness setting is based on the actual water hard -
ness in your house. This information can be obtained from your local
water supplier . The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DR YING easier . The rinse aid dispenser A
should be lled when the RINSE AID REFILL indicator light
in the control panel is lit.
1. Open the dispenser B by pressing and pulling up the tab on
the lid.
2. Carefully introduce the rinse aid as far as the maximum
(1 10 ml) reference notch of the lling space - avoid spilling it.
If this happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the tub.
A
B
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
adjust the quantity of rinse aid used.
• Switch the dishwasher on using the ON/OFF button.
• Switch it of f using the ON/OFF button.
• Press button three times - a beep will be hear d.
• Switch it on using the ON/OFF button.
•
•
The current selection level number and rinse aid indicator light ash.
Press button to select the level of rinse aid qu antity to be
supplied.
• Switch it of f using the ON/OFF button.
Setting is complete!
If the rinse aid level is set to ZERO (ECO), no rinse aid will be
supplied. The LOW RINSE AID indicator light will not be lit if you
run out of rinse aid. A maximum of 5 levels can be set according to
the dishwasher model. The factory setting is specic to the model,
please follow instruction above to check this for your machine.
• If you see bluish streaks on the dishes, set a low number (1-2).
• If there are drops of water or limescale marks on the dishes,
set a high number (3-4).
FILLING THE DETERGENT DISPENSER
������������������������������
dishwashers.
T o achieve the best washing and drying results, the combined
useof detergent, rinse aid liquid and rened salt is required.
W e recommend using detergents that do not contain phosphates
or chlorine, as these products are harmful to the environment.
Good washing results also depend on the correct amount of
detergent being used.
Exceeding the stated amount does not result in a more ef fective
wash and increases environmental pollution.
The amount can be adjusted to the soil level. In the case of
normally soiled items, use approximately either 35g (powder
detergent) or 35ml (liquid detergent) and additional tea spoon of
detergent directly inside the tub. If tablets are used, one tablet
will be enough.
If the crockery is only lightly soiled or if it has been rinsed with
water before being placed in the dishwasher , reduce the amount
of detergent used accordingly (minimum 25 g/ml) e.g. skip the
powder/gel putted inside the tub.
T o open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only .
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
1.
2.
When measuring out the detergent refer to the mentioned ear -
lier information to add the proper quantity . Inside the dispenser
B there are indications to help the detergent dosing.
Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
para
selección.
Nota: Si
indicador de funcionamiento no
ciclo.
NA
El sistema de apertur
por convección que abre la puerta automáticamente dur
después de la fase de secado para gar
ex
temperatur
adicional contra
en el lavavajillas. Para ver cómo montar la lámina pr
consulte (INSTRUCCIONES
La funcionalidad Natur
manera:
1. Vaya al menú del indicador de funcionamiento como en el
último paso y mantenga pulsado el
ENGLISH
8
• Switch on the appliance by pressing the ON/OFF button.
• Switch of f the appliance by pressing the ON/OFF button.
• Hold down button for 5 seconds, until you hear a b eep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
������
Press button to select the desired hardness le vel (see
W A TER HARDNESS T ABLE).
• Switch of f the appliance by pressing the ON/OFF button.
Setting is complete!
W ater Hardness T able
Level °dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 1 1 1 1 - 20
3 A verage 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 V ery hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly , so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-W ash” program alone is NOT ������
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
�������������������������������� s .
��������������������������������
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE W A TER HARDNESS
T o allow the water softener to work in a perfect way , it is essential
that the water hardness setting is based on the actual water hard -
ness in your house. This information can be obtained from your local
water supplier . The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DR YING easier . The rinse aid dispenser A
should be lled when the RINSE AID REFILL indicator light
in the control panel is lit.
1. Open the dispenser B by pressing and pulling up the tab on
the lid.
2. Carefully introduce the rinse aid as far as the maximum
(1 10 ml) reference notch of the lling space - avoid spilling it.
If this happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the tub.
A
B
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
adjust the quantity of rinse aid used.
• Switch the dishwasher on using the ON/OFF button.
• Switch it of f using the ON/OFF button.
• Press button three times - a beep will be hear d.
• Switch it on using the ON/OFF button.
•
•
The current selection level number and rinse aid indicator light ash.
Press button to select the level of rinse aid qu antity to be
supplied.
• Switch it of f using the ON/OFF button.
Setting is complete!
If the rinse aid level is set to ZERO (ECO), no rinse aid will be
supplied. The LOW RINSE AID indicator light will not be lit if you
run out of rinse aid. A maximum of 5 levels can be set according to
the dishwasher model. The factory setting is specic to the model,
please follow instruction above to check this for your machine.
• If you see bluish streaks on the dishes, set a low number (1-2).
• If there are drops of water or limescale marks on the dishes,
set a high number (3-4).
FILLING THE DETERGENT DISPENSER
������������������������������
dishwashers.
T o achieve the best washing and drying results, the combined
useof detergent, rinse aid liquid and rened salt is required.
W e recommend using detergents that do not contain phosphates
or chlorine, as these products are harmful to the environment.
Good washing results also depend on the correct amount of
detergent being used.
Exceeding the stated amount does not result in a more ef fective
wash and increases environmental pollution.
The amount can be adjusted to the soil level. In the case of
normally soiled items, use approximately either 35g (powder
detergent) or 35ml (liquid detergent) and additional tea spoon of
detergent directly inside the tub. If tablets are used, one tablet
will be enough.
If the crockery is only lightly soiled or if it has been rinsed with
water before being placed in the dishwasher , reduce the amount
of detergent used accordingly (minimum 25 g/ml) e.g. skip the
powder/gel putted inside the tub.
T o open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only .
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
1.
2.
When measuring out the detergent refer to the mentioned ear -
lier information to add the proper quantity . Inside the dispenser
B there are indications to help the detergent dosing.
Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
hasta que el menú
aparezca.
2. Para ir al menú de Natur
ENGLISH
8
• Switch on the appliance by pressing the ON/OFF button.
• Switch of f the appliance by pressing the ON/OFF button.
• Hold down button for 5 seconds, until you hear a b eep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
������
Press button to select the desired hardness le vel (see
W A TER HARDNESS T ABLE).
• Switch of f the appliance by pressing the ON/OFF button.
Setting is complete!
W ater Hardness T able
Level °dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 1 1 1 1 - 20
3 A verage 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 V ery hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly , so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-W ash” program alone is NOT ������
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
�������������������������������� s .
��������������������������������
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE W A TER HARDNESS
T o allow the water softener to work in a perfect way , it is essential
that the water hardness setting is based on the actual water hard -
ness in your house. This information can be obtained from your local
water supplier . The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DR YING easier . The rinse aid dispenser A
should be lled when the RINSE AID REFILL indicator light
in the control panel is lit.
1. Open the dispenser B by pressing and pulling up the tab on
the lid.
2. Carefully introduce the rinse aid as far as the maximum
(1 10 ml) reference notch of the lling space - avoid spilling it.
If this happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the tub.
A
B
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
adjust the quantity of rinse aid used.
• Switch the dishwasher on using the ON/OFF button.
• Switch it of f using the ON/OFF button.
• Press button three times - a beep will be hear d.
• Switch it on using the ON/OFF button.
•
•
The current selection level number and rinse aid indicator light ash.
Press button to select the level of rinse aid qu antity to be
supplied.
• Switch it of f using the ON/OFF button.
Setting is complete!
If the rinse aid level is set to ZERO (ECO), no rinse aid will be
supplied. The LOW RINSE AID indicator light will not be lit if you
run out of rinse aid. A maximum of 5 levels can be set according to
the dishwasher model. The factory setting is specic to the model,
please follow instruction above to check this for your machine.
• If you see bluish streaks on the dishes, set a low number (1-2).
• If there are drops of water or limescale marks on the dishes,
set a high number (3-4).
FILLING THE DETERGENT DISPENSER
������������������������������
dishwashers.
T o achieve the best washing and drying results, the combined
useof detergent, rinse aid liquid and rened salt is required.
W e recommend using detergents that do not contain phosphates
or chlorine, as these products are harmful to the environment.
Good washing results also depend on the correct amount of
detergent being used.
Exceeding the stated amount does not result in a more ef fective
wash and increases environmental pollution.
The amount can be adjusted to the soil level. In the case of
normally soiled items, use approximately either 35g (powder
detergent) or 35ml (liquid detergent) and additional tea spoon of
detergent directly inside the tub. If tablets are used, one tablet
will be enough.
If the crockery is only lightly soiled or if it has been rinsed with
water before being placed in the dishwasher , reduce the amount
of detergent used accordingly (minimum 25 g/ml) e.g. skip the
powder/gel putted inside the tub.
T o open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only .
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
1.
2.
When measuring out the detergent refer to the mentioned ear -
lier information to add the proper quantity . Inside the dispenser
B there are indications to help the detergent dosing.
Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
de
nuevo dur
3. Ha cambiado al Menú de
el estado de la
botón
ENGLISH
8
• Switch on the appliance by pressing the ON/OFF button.
• Switch of f the appliance by pressing the ON/OFF button.
• Hold down button for 5 seconds, until you hear a b eep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
������
Press button to select the desired hardness le vel (see
W A TER HARDNESS T ABLE).
• Switch of f the appliance by pressing the ON/OFF button.
Setting is complete!
W ater Hardness T able
Level °dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 1 1 1 1 - 20
3 A verage 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 V ery hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly , so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-W ash” program alone is NOT ������
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
�������������������������������� s .
��������������������������������
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE W A TER HARDNESS
T o allow the water softener to work in a perfect way , it is essential
that the water hardness setting is based on the actual water hard -
ness in your house. This information can be obtained from your local
water supplier . The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DR YING easier . The rinse aid dispenser A
should be lled when the RINSE AID REFILL indicator light
in the control panel is lit.
1. Open the dispenser B by pressing and pulling up the tab on
the lid.
2. Carefully introduce the rinse aid as far as the maximum
(1 10 ml) reference notch of the lling space - avoid spilling it.
If this happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the tub.
A
B
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
adjust the quantity of rinse aid used.
• Switch the dishwasher on using the ON/OFF button.
• Switch it of f using the ON/OFF button.
• Press button three times - a beep will be hear d.
• Switch it on using the ON/OFF button.
•
•
The current selection level number and rinse aid indicator light ash.
Press button to select the level of rinse aid qu antity to be
supplied.
• Switch it of f using the ON/OFF button.
Setting is complete!
If the rinse aid level is set to ZERO (ECO), no rinse aid will be
supplied. The LOW RINSE AID indicator light will not be lit if you
run out of rinse aid. A maximum of 5 levels can be set according to
the dishwasher model. The factory setting is specic to the model,
please follow instruction above to check this for your machine.
• If you see bluish streaks on the dishes, set a low number (1-2).
• If there are drops of water or limescale marks on the dishes,
set a high number (3-4).
FILLING THE DETERGENT DISPENSER
������������������������������
dishwashers.
T o achieve the best washing and drying results, the combined
useof detergent, rinse aid liquid and rened salt is required.
W e recommend using detergents that do not contain phosphates
or chlorine, as these products are harmful to the environment.
Good washing results also depend on the correct amount of
detergent being used.
Exceeding the stated amount does not result in a more ef fective
wash and increases environmental pollution.
The amount can be adjusted to the soil level. In the case of
normally soiled items, use approximately either 35g (powder
detergent) or 35ml (liquid detergent) and additional tea spoon of
detergent directly inside the tub. If tablets are used, one tablet
will be enough.
If the crockery is only lightly soiled or if it has been rinsed with
water before being placed in the dishwasher , reduce the amount
of detergent used accordingly (minimum 25 g/ml) e.g. skip the
powder/gel putted inside the tub.
T o open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only .
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
1.
2.
When measuring out the detergent refer to the mentioned ear -
lier information to add the proper quantity . Inside the dispenser
B there are indications to help the detergent dosing.
Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
:
E – activado d – desactivado
ParaconrmarelcambioysalirdelMenúdecontr
pulsado el botón
ENGLISH
8
• Switch on the appliance by pressing the ON/OFF button.
• Switch of f the appliance by pressing the ON/OFF button.
• Hold down button for 5 seconds, until you hear a b eep.
• Switch on the appliance by pressing the ON/OFF button.
•
•
The current selection level number and the salt indicator light
������
Press button to select the desired hardness le vel (see
W A TER HARDNESS T ABLE).
• Switch of f the appliance by pressing the ON/OFF button.
Setting is complete!
W ater Hardness T able
Level °dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 1 1 1 1 - 20
3 A verage 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 V ery hard 35 - 50 61 - 90
Make sure the cap is screwed on tightly , so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The “Pre-W ash” program alone is NOT ������
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
�������������������������������� s .
��������������������������������
heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle.
SETTING THE W A TER HARDNESS
T o allow the water softener to work in a perfect way , it is essential
that the water hardness setting is based on the actual water hard -
ness in your house. This information can be obtained from your local
water supplier . The factory setting is for average (3) water hardness.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DR YING easier . The rinse aid dispenser A
should be lled when the RINSE AID REFILL indicator light
in the control panel is lit.
1. Open the dispenser B by pressing and pulling up the tab on
the lid.
2. Carefully introduce the rinse aid as far as the maximum
(1 10 ml) reference notch of the lling space - avoid spilling it.
If this happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the tub.
A
B
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satised with the drying results, you can
adjust the quantity of rinse aid used.
• Switch the dishwasher on using the ON/OFF button.
• Switch it of f using the ON/OFF button.
• Press button three times - a beep will be hear d.
• Switch it on using the ON/OFF button.
•
•
The current selection level number and rinse aid indicator light ash.
Press button to select the level of rinse aid qu antity to be
supplied.
• Switch it of f using the ON/OFF button.
Setting is complete!
If the rinse aid level is set to ZERO (ECO), no rinse aid will be
supplied. The LOW RINSE AID indicator light will not be lit if you
run out of rinse aid. A maximum of 5 levels can be set according to
the dishwasher model. The factory setting is specic to the model,
please follow instruction above to check this for your machine.
• If you see bluish streaks on the dishes, set a low number (1-2).
• If there are drops of water or limescale marks on the dishes,
set a high number (3-4).
FILLING THE DETERGENT DISPENSER
������������������������������
dishwashers.
T o achieve the best washing and drying results, the combined
useof detergent, rinse aid liquid and rened salt is required.
W e recommend using detergents that do not contain phosphates
or chlorine, as these products are harmful to the environment.
Good washing results also depend on the correct amount of
detergent being used.
Exceeding the stated amount does not result in a more ef fective
wash and increases environmental pollution.
The amount can be adjusted to the soil level. In the case of
normally soiled items, use approximately either 35g (powder
detergent) or 35ml (liquid detergent) and additional tea spoon of
detergent directly inside the tub. If tablets are used, one tablet
will be enough.
If the crockery is only lightly soiled or if it has been rinsed with
water before being placed in the dishwasher , reduce the amount
of detergent used accordingly (minimum 25 g/ml) e.g. skip the
powder/gel putted inside the tub.
T o open the detergent dispenser
press button A.
Introduce the detergent into
the dry dispenser B only .
Place the amount of detergent
for pre-washing directly inside
the tub.
A
B
1.
2.
When measuring out the detergent refer to the mentioned ear -
lier information to add the proper quantity . Inside the dispenser
B there are indications to help the detergent dosing.
Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
(3seg.).
APERTURA DE LA PUERT
Eco 50° pasados 165 min
AUTO 50°- 60° 80-170 min*
Intensivo 65° n del ciclo
Lavado rápido 30’ 50° N/A
Lavado rápido y secado 50° n del ciclo
Vidrio 45° n del ciclo
Silencioso 50° n del ciclo
Desinfección 65° N/A
Prelavado N/A
Autolimpieza 65° N/A
* dependiendo de la
Progr Fase
de
secado
Natural
Dry Funciones
disponibles *) Duración del
progr
lavado (h:min)**)
Consumo
de agua
(litros/ciclo)
Consumo
energético
(kWh/ciclo)
1 Eco
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
50°
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
3:40 8.7 0.59
2 Auto
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
50-60°
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensivo
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
65°
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
2:40 17.0 1.30
4 Lavado rápido 30’
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
50° - -
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
0:30 9.0 0.50
5
Lavado y secado rápido
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
50°
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
1:20 10.0 1.10
6 Vidrio
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
45°
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
1:40 12.0 1.00
7 Silencioso
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
50°
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
3:35 16.5 1.00
8 Desinfección
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
65°
9
ENGLISH
1. Press the DELA Y button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the ST AR T/P AUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
switches of f and the wash cycle begins.
T o adjust the delay time and select a shorter period of time,
press the DELA Y button. T o cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches of f.
The DELA Y function cannot be set once a wash cycle
has been started.
NaturalDry
Door opening system NaturalDry is a convection drying system
which automatically opens the door during/after drying phase to
ensure exceptional drying performance every day . Door opens at
the temperature that is safe to your kitchen furniture.
As additional steam protection, special designed protection foil is
added together with the dishwasher . T o see how to mount protec-
tion foil please refer to (INST ALLA TION GUIDE) .
NaturalDry functionality could be disabled by the user as follows:
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. Y ou switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing button:
E – enabled d – disabled
T o conrm the change and exit from the Control Menu please
press and hold button (3 sec).
DELA Y
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
Program
Drying
phase
Natural
Dry
A vailable
options *)
Duration of
wash pro-
gram
(h:min) **)
W ater
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50° 2:45 12.0 0.92
1 Eco
2 Conventional
wash and dry 55° 2:00 15.0 1.35
3 Intensive 65° - 2:30 15.0 1.50
4 Fast 50° - - 0:55 1 1.5 1.10
5 Sanitizing 65° - 1:40 1 1.5 1.30
6 Pre-W ash
-
- - 0:10 4.5 0.01
7 Self-Clean 65° - - 0:50 8.0 0.80
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing conditions, please send an email to the following
address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programes other than the eco program are indicative only. The actual time may vary depending on many
factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of
load, load balancing, additional selected options and sensor calibration.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
-
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
1:40 12.0 1.30
9 Prelavado
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
- -
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
0:10 4.5 0.01
10
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
65° - -
EN
9
T o op e n t h e d eter g e n t di s p e n se r
press button C.
Introduce the detergent into
the dry dispenser D onl y .
Place the amount of detergent
for pre-washing directly inside
the tub.
1. When measuring out the detergent refer to the mentioned ear-
lier information to add the proper quantity . Inside the dispenser
C there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program. If all-in-one detergents are used, we
recommend using the T ABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved.
C
D
PROGRAMS T ABLE
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2019.
Note for T est Laboratories: For information on comparative EN testing condit ions, please send an email to the following address:
dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneousl y .
**) V alues given for programes other than the eco program are indicative only . The actual time may vary depending on many factors such as temperature
and pressure of the incoming water , room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and
sensor calibration.
Standby consumpti on: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
1. ECO -
bined energy and water consumption, and that it is used to asses s compliance with the EU Ecodesign legislation.
2. AUT O - For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accor -
dingl y . When the sensor is detecting the soil level an animation ap pears in the display and the cycle duration is updated.
3 . I N TE N SIVE -
P rogram recommended f or hea v il y soiled cro c ker y , e s pe c iall y sui t able f or pan s and s au c epan s (no t t o be u s ed f or delica t e i t em s ) .
4. F AST W ASH 30’ - Program to be used for half load of lightly-soile d dishes with no dried food residues.
5. F AST W ASH AND DR Y
- Normally soiled crockery . Everyday cycle, that ensures optimal cleaning and drying performance in shorter time.
6. GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
7. SILENT -
Suitable for night-time operation of the appliance. Ensures optimal cleaning and drying performance with the lowest noise emission.
8. SANITIZING - Normally or heavily soiled crockery , with additiona l antibacterial wash. Can be used to perform maintenance of the
dishwashe r .
9. PRE-W ASH - Use to refresh crockery planned to be washed late r . No detergent to be used with this program.
10. SELF-CLEAN - Program to be used to perform maintenance of the dishwasher . It cleans the interior of the appliance using hot water .
Notes:
Please note that cycle F AST W ASH is dedicated for lightly soiled dish es.
Program
Dry in g
ph as e
Natural
Dry
A vailable
option s *)
Duration of
wash
program
(h:min) **)
W ater
consumption
(litres/cycle)
En er g y
c on s u m p t io n
(kWh/cycle)
1 Eco 3:40 8.7 0.66
2 Auto 1:20 - 3:00 7.0 - 14.0 0.70 - 1.10
3 Intensive 2:40 17.0 1.30
4 Fast wash 30’ - - 0:30 9.0 0.50
5 1:20 10.0 1.10
6 Glass 1:40 12.0 1.00
7 Silent 3:35 16.5 1.00
8 Sanitizing - 1:40 12.0 1.30
9 Pre-W ash - - 0:10 4.5 0.01
10 Self- Clean - - 0:50 9.5 0.70
0:50 9.5 0.70
Los datos del progr
laboratorio de
Nota par
las condiciones de la
electrónico a la siguiente dir
dw_test_support@whirlpool.com
No es necesario ningún
ninguno de los progr
*) No todas las
**) Los valores indicados par
progr
dependiendo de muchos factor
presión del agua de entr
de detergente, la
carga, las opciones
sensor
1. ECO: El pr
suciedad normal, par
en términos de consumo
se utiliza para valor
Ecodiseño de la UE.
2. AUTO - Par
comida secos. Detecta el
ajusta el progr
detectando el nivel de suciedad, aparece una animación en la
pantalla y se actualiza
3. INTENSIVO - Pr
en especial par
artículos delicados).
4. LAV Programa par
de vajilla con suciedad normal. Garantiza un lavado óptimo
en poco tiempo.
5. LA - Vajilla normalmente sucia.
Ciclo diario que garantiza un r
secado óptimos en poco tiempo.
6. VIDRIO - Progr
temperatur
7. SILENCIOSO - Adecuado par
de noche. Garantiza una limpieza y un secado óptimos con
las más bajas emisiones de ruido.
8. DESINFECCIÓN: V
con acción antibacteriana suplementaria. Puede utilizarse
para r
9. PRELA Se utiliza para r
lavar más tarde. Con este pr
detergente.
10. Progr
del lavavajillas. Solo debe llevarse a cabo cuando el
lavavajillas esté V
diseñados para el mantenimiento de lavavajillas.
Notas: T
platos con poca suciedad.
Las FUNCIONES se pueden seleccionar directamente pulsando
el botón correspondiente (consulte P
Si una función no es compatible con el progr
seleccionado consulte la T
correspondienteparpadear
unos pitidos. La opción no se habilitará.
