ENGLISH 13
What to do if ...
In case your dishwasher doesn’t work properly
following list. For other err
be found in the warranty booklet. The manufactur
after production date of this appliance.
Problems... Possible causes... Solutions...
What t o do if ... What t o do if ...
In case your dishwasher doesn’t work properly , check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty
booklet. The manufacturer ensures the availability of spare parts for at least 10 years after production date of this appliance.
PROBLEMS POSSIBLE CAUSES SOLUTIONS
Salt indicator is lit
Salt reservoir is empty . (After refill
the salt indicator may remain lit
for several wash cycles).
Refill reservoir with sal (for more information - see page 8).
Adjust water hardness - see table, page 8 .
Rinse aid indicator is lit
Rinse aid dispenser is empty .
(After refill the rinse aid indicator
may remain lit for several wash
cycles).
Refill dispenser with rinse aid (for more information - see page 8) .
The dishwasher won’t start
or does not respond to
commands.
The appliance has not been
plugged in properly . Insert the plug into the socket.
Power outage. The dishwasher starts automatically when the power returns.
The dishwasher door is not closed. V igorously push the door until you hear the “click” .
It does not respond to commands.
Display shows: 9 or 12 and
On/Of f LED is blinking rapidly .
Switch of f the appliance by pressing the ON/OFF button, switch it
back on after approximately one minute and reset the program.
If problem persists, unplug the appliance for 1 minute, then plug it
back in.
The dishwasher won’t drain.
Display shows: 3 and
On/Of f LED is blinking
rapidly
The wash cycle has not finished yet W ait until the wash cycle finishes
The drain hose is bent. Check that the drain hose is not bent (see INST ALLA TION).
The sink drain pipe is blocked. Clean the sink drain pipe.
The filter is clogged up with food
residues. Clean the filter (see CLEANING THE FIL TER ASSEMBL Y).
The dishwasher makes
excessive noise.
The dishes are rattling against
each. Arrange the crockery correctly (see LOADING THE RACKS).
An excessive amount of foam has
been produced.
The detergent has not been measured out correctly or it is not
suitable for use in dishwashers (see FILLING THE DETERGENT
DISPENSER) . Reset the current cycle by switching OFF the
dishwasher , then switch it on again, select a new program, press
ST AR T/Pause and close the door within 4 seconds. Please do not
add any detergent.
The dishes are not clean.
The crockery has not been
arranged properly . Arrange the crockery correctly (see LOADING THE RACKS).
The spray arms cannot rotate freely ,
being hindered by the dishes. Arrange the crockery correctly (see LOADING THE RACKS).
The wash cycle is too gentle
and/or detergent efficiency is lo . Select an appropriate wash cycle (see PROGRAMS T ABLE).
An excessive amount of foam has
been produced.
The detergent has not been measured out correctly or it is not suitable
for use in dishwashers ( see FILLING THE DETERGENT DISPENSER) .
The cap on the rinse aid compart -
ment has not been shut correctly . Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged Clean the filter assembly (see CARE AND MAINTENANCE).
There is no salt. Fill the salt reservoir (see FILLING THE SAL T RESER VOIR).
The dishwasher does not fill
the water .
Display shows: H
6
and On/Of f LED is blin-
king
rapidly
No water in the water supply or
the tap is closed. Make sure there is water in the water supply or the tap running.
The inlet hose is bent. Make sure the inlet hose is not bent (see INST ALLA TION) repro-
gram the dishwasher and reboot.
The sieve in the water inlet hose
is clogged; it is necessary to
clean it.
After having carried out the verification and cleaning, turn o f and
turn on the dishwasher and restart a new program.
Salt indicator is lit
Salt reservoir is empty
rell the
remain lit for se
cycles).
Rell reservoir with sal (for mor
Adjust water hardness - see table, page 8.
What t o do if ... What t o do if ...
In case your dishwasher doesn’t work properly , check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty
booklet. The manufacturer ensures the availability of spare parts for at least 10 years after production date of this appliance.
PROBLEMS POSSIBLE CAUSES SOLUTIONS
Salt indicator is lit
Salt reservoir is empty . (After refill
the salt indicator may remain lit
for several wash cycles).
Refill reservoir with sal (for more information - see page 8).
Adjust water hardness - see table, page 8 .
Rinse aid indicator is lit
Rinse aid dispenser is empty .
(After refill the rinse aid indicator
may remain lit for several wash
cycles).
Refill dispenser with rinse aid (for more information - see page 8) .
The dishwasher won’t start
or does not respond to
commands.
The appliance has not been
plugged in properly . Insert the plug into the socket.
Power outage. The dishwasher starts automatically when the power returns.
The dishwasher door is not closed. V igorously push the door until you hear the “click” .
It does not respond to commands.
Display shows: 9 or 12 and
On/Of f LED is blinking rapidly .
Switch of f the appliance by pressing the ON/OFF button, switch it
back on after approximately one minute and reset the program.
If problem persists, unplug the appliance for 1 minute, then plug it
back in.
The dishwasher won’t drain.
Display shows: 3 and
On/Of f LED is blinking
rapidly
The wash cycle has not finished yet W ait until the wash cycle finishes
The drain hose is bent. Check that the drain hose is not bent (see INST ALLA TION).
The sink drain pipe is blocked. Clean the sink drain pipe.
The filter is clogged up with food
residues. Clean the filter (see CLEANING THE FIL TER ASSEMBL Y).
The dishwasher makes
excessive noise.
The dishes are rattling against
each. Arrange the crockery correctly (see LOADING THE RACKS).
An excessive amount of foam has
been produced.
The detergent has not been measured out correctly or it is not
suitable for use in dishwashers (see FILLING THE DETERGENT
DISPENSER) . Reset the current cycle by switching OFF the
dishwasher , then switch it on again, select a new program, press
ST AR T/Pause and close the door within 4 seconds. Please do not
add any detergent.
The dishes are not clean.
The crockery has not been
arranged properly . Arrange the crockery correctly (see LOADING THE RACKS).
The spray arms cannot rotate freely ,
being hindered by the dishes. Arrange the crockery correctly (see LOADING THE RACKS).
The wash cycle is too gentle
and/or detergent efficiency is lo . Select an appropriate wash cycle (see PROGRAMS T ABLE).
An excessive amount of foam has
been produced.
The detergent has not been measured out correctly or it is not suitable
for use in dishwashers ( see FILLING THE DETERGENT DISPENSER) .
The cap on the rinse aid compart -
ment has not been shut correctly . Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged Clean the filter assembly (see CARE AND MAINTENANCE).
There is no salt. Fill the salt reservoir (see FILLING THE SAL T RESER VOIR).
The dishwasher does not fill
the water .
Display shows: H
6
and On/Of f LED is blin-
king
rapidly
No water in the water supply or
the tap is closed. Make sure there is water in the water supply or the tap running.
The inlet hose is bent. Make sure the inlet hose is not bent (see INST ALLA TION) repro-
gram the dishwasher and reboot.
The sieve in the water inlet hose
is clogged; it is necessary to
clean it.
After having carried out the verification and cleaning, turn o f and
turn on the dishwasher and restart a new program.
Rinse aid indicator is lit
Rinse aid dispenser is empty
(After r
may remain lit for se
cycles).
Rell dispenser with rinse aid (for more information - see
page 8).
The dishwasher won’t start
or does not respond to
commands.
The appliance has not been
plugged in properly Insert the plug into the socket.
Power outage. For safety reasons, dishwasher will not r
when power r
button and close the door within 4 seconds.
The dishwasher door is not
closed.
Natural Dry pin is not pulled in.
Vigorously push the door until you hear the “
It does not respond to
commands. Display shows: 9 or
12 and On/O LED is blinking
rapidly
Switch o the appliance by pr
switch it back on after appro
the progr
minute, then plug it back in.
The dishwasher won’t drain.
Display shows: 3 and
On/O LED is blinking
rapidly
The wash cycle has not nished
yet Wait until the wash cycle nishes
The drain hose is bent. Check that the drain hose is not bent (see INST
The sink drain pipe is blocked. Clean the sink dr
The lter is clogged up with food
residues. Clean the lter (see CLEANING THE FIL
The dishwasher makes
ex
The dishes are r
each. Arrange the cr
An ex
has been produced. The detergent has not been measured out corr
suitable for use in dishwashers (see FILLING THE DETERGENT
DISPENSER). Restart the current cycle b
dishwasher
press ST
Please do not add any detergent.
The dishes are not clean.
The crockery has not been
arranged pr Arrange the cr
The spray arms cannot r
freely
dishes.
Arrange the cr
The wash cycle is too gentle
and/or detergent eciency is
l
Select an appropriate wash cycle (see PROGRAMS T
An ex
has been produced. The detergent has not been measured out corr
suitable
for use in dishwashers (see FILLING THE DETERGENT
DISPENSER).
The cap on the rinse aid
compartment has not been shut
correctly
Make sure the cap of the rinse aid dispenser is closed.
The lter is soiled or clogged Clean the lter assembly (see CARE AND MAINTENANCE).
There is no salt. Fill the salt reservoir (see FILLING THE SAL
