Bedienungsanleitung Innoliving INN-508 (Seite 12 von 16) (Englisch, Italienisch)

800608

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

medium speed and the low speed and a pause of 6 seconds.

2. If the fan speed is set to MID, the Natural mode will alternate the medium speed, the low

speed and a pause of about 6 seconds.

3. If the fan speed is set to LOW, the Natural mode will alternate only the low speed with a

pause of approximately 6 seconds.

Sleep Mode (Sleep): ventilation alternates between different ventilation speeds, then reduces

to remain constant. The lowering of the fan speed depends on the previously set speed with

the “Speed” button:

1. If the ventilation speed is set to HIGH, the Sleep mode will alternate the maximum speed,

the medium speed, the low speed and a pause of around 6 seconds. After 30 minutes, the

speed will remain constant at the medium speed of ventilation.

2. If the ventilation speed is set to MID, the Sleep mode will alternate the medium speed, the

low speed and a pause of about 6 seconds. After 30 minutes, the speed will remain constant

at the low speed of ventilation.

3. If the fan speed is set to LOW, the Natural mode will alternate only the low speed with a

pause of approximately 6 seconds. After 30 minutes, the speed will remain constant at the

low speed of ventilation.

4. Timer: press the “Timer” key to set the operating time of the fan (from 0 to 12 hours). This

setting allows the unit to enter standby mode after the set time. Press the “Timer” button to

increase the operating time of one unit at a time. To deactivate this function, simply press the

“Timer” button until the display shows “00”.

5. Swing: press the “Swing” key to activate the swinging function of the aps Once the

“swing” button has been pressed, the appropriate icon will appear on the control panel.To

deactivate the swing function, press the “Swing” button again. The airow direction can be

adjusted manually by arranging air wings.

6. Cooler: press the “Cooler” button to activate the cooling function.

Attention: do not activate the cooling function if the water level in the tank is below the

minimum level indicated or there is no water in the tank.

Before activating this function, check the water level and ll the tank if necessary. Replace

stale water with fresh water. It is advisable to replace the water in the tank at least once a

week.

Once the “cooling” function has been activated, the water pump will start to draw water

from the tank, making it pass through the cooling pad; in this way the evaporated air is

expelled with the help of the fan.

7. Ionizer: press the “Ion” button to activate the ionizer function. The appropriate function

icon will light up on the display and the release of negative ions will start.

HEATING FUNCTION:

Set the switch (5) in the Heating position.

1. ON / OFF: Press the “ON / OFF” button on the control panel or press the ON / OFF button

on the remote control to turn the unit on. The unit will start with a normal ventilation speed

and a low heating level (1000 W).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Innoliving INN-508 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info