Bedienungsanleitung Innoliving INN-508 (Seite 13 von 16) (Englisch, Italienisch)

800608

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

After pressing the ON / OFF button for the second time, the device will stop emitting heat but

the fan will remain in operation for another 30 seconds, after which the device will return to

stand-by mode.

2. Speed: the speed selection function is not available when the product is in “Heating” mode.

3. Wind/heat: Press the “Wind / Heat” button to select the desired heat intensity. Each time

this button is pressed, an indicator will light up on the screen to indicate the type of intensity

selected. There are 2 levels of heating intensity: low (1000W) or high (2000W).

4. Timer: press the “Timer” key to set the operating time of the fan (from 0 to 12 hours). This

setting allows the unit to enter standby mode after the set time. Press the “Timer” button to

increase the operating time of one unit at a time. To deactivate this function, simply press the

“Timer” button until the display shows “00”.

5. Swing: press the “Swing” key to activate the swing function of the wings. Once the “swing”

button is pressed, the appropriate icon will appear on the control panel. To deactivate the

swing function, press the “Swing” key again. The airow direction can be adjusted manually

by arranging the appropriate air wings.

6. Cooler: the cooling function is not available when the product is in “Heating” mode.

7. Ionizer: press the “Ion” button to activate the ionizer function. The appropriate function

icon will light up on the display and the release of negative ions will start.

How to ﬁll the tank

Check the water level in the tank frequently, making sure that it never goes below the “MIN”

level indicated in the tank itself. The activation of the “cooling” function with an insufcient

amount of water may cause the malfunction of the water pump making void the warranty.

ATTENTION: Before proceeding with the ﬁlling of the tank, make sure to ﬁrst

disconnect the device to the mains.

How to use ice tablets

By inserting the ice tablets into the tank, a fresher jet of air can be obtained.

• Store them for a couple of hours in the freezer.

• Once the water is frozen inside them, the ice boards are ready to be stored in the tank.

Proceed by pouring the water into the tank until reaching the indicated MAX level.

CLEANING AND MAINTENANCE

Dust accumulating on the dust lter may prevent proper air ow. Therefore we recommend to

clean the lter and all its parts regularly, following the instructions below. Before proceeding

with any maintenance or cleaning operation, switch off the appliance and remove the plug

form the main socket. Never clean the product components with ammable liquids. The

vapours may cause re or explosion.

Dust Filter

To remove the dust lter, simply press the two release levels located at the top of the lter

down to remove it. Use a mild detergent and a soft brush to clean and remove dust and dirt

from the lter. Put the lter on again inserting the bottom rstly and pushing the upper part

to lock it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Innoliving INN-508 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info