Bedienungsanleitung Intex CS20110 Krystal Clear (Seite 21 von 38) (Englisch)

752348

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012

159

SAVE THESE INSTRUCTIONS

Page 21

English

SALTWATER SYSTEM OPERATION (continued)

OPERATING INSTRUCTIONS

6. Boost cycle

• Ifthetestresultisbelow0.1ppm,pressandhold“BOOST”

button for 5 seconds until the indicator lights up and the

LED display display “80”. This indicates that the saltwater

system has started copper ion and more chlorine sanitizer

 production.Youcanpressandholdthe“BOOST”buttonfor

another 5 seconds until the indicator is off, which will cancel

 theBoostcycle.

Note: Once the system has started copper ion and more

chlorine sanitizer production, the boost button can’t be re-set until the power

switch is off.

• The boost operating hours is 8 times the amount of time programmed into the

system, i.e. if your saltwater system operating time is 2 hours, the boost procedure

will run 8 x 2 = 16 hours. After boost procedure has been completed, the system

will automatically switch to the normal working mode.

• Afteraheavyrainorifthepoolisdirty,pressthe“BOOST”buttontoshockthe

pool again.

7. Test pool water regularly:

Once the copper level appears to be balanced, test the pool water every week

to maintain the proper sanitizer level.

It’s very important that the free chlorine is between 0.5-3 ppm and copper

ion concentration is between 0.1~0.2 ppm. When the copper level is below 0.1

ppm, repeat step 6.

NOTE:AHighcopperionconcentrationmaycauseblondehairtoexhibita 

green hair. To prevent this, wear a swimming cap during swimming, and wash

hair with special shampoo after using the pool.

 See“TroubleshootingGuide”.

8. Stand-by/power saving mode:

• When the cycle ends, the green “SLEEP” indicator on the

control panel lights up and the LED display flashes “93”.

 ThesystemisnowinStand-Bymode.Afterawhile,it 

shuts down and sets itself in a Power Saving mode. The

system will automatically turn itself back on in 24 hours,

starting its daily cycle of chlorine production.

• The “SLEEP” indicator stays on, while the system is in the

Power Saving mode. The LED display however, goes blank

after 1 hour. Press any button ( or ) to view the last LED

code.

9. Running the pump alone without the Saltwater System:

To run the pump alone without the Saltwater System function,

press and hold both ( ) and ( ) buttons for 5 seconds

 untilyouheara“beep”andtheLEDdisplayshows“FP”.

The pump is now operating alone. To stop the pump,

 manuallyturntheswitchOFF.NOTE: The pump cannot

be operated alone under an automatic timer mode.

IMPORTANT: To keep the initial automatic operating cycle

 settingoftheSaltwaterSystem,turntheswitchON,the

 LEDdisplayshows“FP”,thenunlockandlockthekeypad

controls again, see previous steps 2 and 3. The LED display shows

the initial input hours and the Saltwater System cycle repeats again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex CS20110 Krystal Clear Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info