Bedienungsanleitung Intex CS20110 Krystal Clear (Seite 23 von 38) (Englisch)

752348

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012

159

SAVE THESE INSTRUCTIONS

Page 23

English

SALT & POOL WATER VOLUMES

• Whichkindofsalttouse:

Use only Sodium Chloride Salts

Useonlysodiumchloride(NaCl)saltthatisatleast99.8%pure.Itisalso

acceptable to use water conditioning salt pellets (the compressed forms of

evaporatedsalt).However,itwilltakealongertimeforthemtodissolve.Do not

use iodized or yellow (yellow prussiate of soda) colored salt. Salt is added to

the pool water and the electrolytic cell uses the salt to create the sanitizer. So, the

purer the salt the better the performance of the electrolytic cell.

• OptimumSaltLevels

The ideal salt level in the pool water is between 2500-3500 ppm (parts per million).

The optimal level is 3000 ppm.

A too low salt level will reduce the efficiency of the saltwater system and result in

low sanitizer production. A high salt level may generate a salty taste to the pool

water (this may occur at a salt level above 3500-4000ppm). Too high of a salt level

may damage the power supply and cause corrosion to pool metal fixtures and

accessories. The Salt Table page of this manual, shows the correct dosage of salt

needed. The salt in the pool is constantly recycled. Salt loss occurs only when pool

water is physically removed from the pool. Salt is not lost due to evaporation.

• AddingSalt

1. Switch on the unit, then press and hold both and button for 5 seconds,

 theLEDflashes“FP”.TheunitisnowinaFilterpumpworkingmodeand 

switch the filter pump on to start the water circulation.

2. KeeptheSaltwaterSystemturnedoff.

3. Determine the amount of salt to be added (see “Salt Table”).

4. Evenly spread the proper amount of salt around the inside perimeter of the

pool.

5. Avoid clogging the filter by not adding salt through the skimmer.

6. Brushthepoolbottomtospeedupthedissolvingprocess.Donotallowsaltto

pile up on the bottom of the pool. Run the filter pump 24 consecutive hours to

thoroughly dissolve the salt.

7. After 24 hours and if all the salt is dissolved, turn on the Saltwater System,

press button until you hear a “beep”, code “00” flashing (see “System

Operation” section steps 2 to 4) and set the saltwater pool system to desired

operating time (see “Operating Time Table”).

• RemovingSalt

If too much salt has been added, the unit will beep and display “Code 92” (see “Alarm

Codes”).Youwillneedtolowerthesaltconcentration.Theonlywaytodoso,isto

partially drain the pool and refill it with fresh water. Drain and refill

approximately20%ofthepool’swateruntilthe“Code92”disappears.

• PoolVolumeCalculation

Rectangular

Length x Width x Average Depth x 7.5 Length x Width x Average Depth

Circular

Length x Width x Average Depth x 5.9 Length x Width x Average Depth x 0.79

Oval

Length x Width x Average Depth x 6.0 Length x Width x Average Depth x 0.80

Types of Pool Gallons

(pool size in feet)

Cubic Meters

(pool size in meters)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex CS20110 Krystal Clear Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info