Bedienungsanleitung Intex PureSpa - 28492 PS-BH-20 (Seite 18 von 34) (Englisch)

686578

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

344

NLA

S AVE THESE INSTRUCTIONS

(344NL) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/09/2019

English

Page 18

SPA CONTROL PANEL

J: Heater Duration Timer (HDT) Button

K: Celsius/Fahrenheit Toggle Button

L: Decrease Button

M: Increase Button

N: LED Display

OPERATION (continued)

Heater Duration Timer (HDT) Button: Use this button to select the desired length of time the

heating system should operate. Press this button and then press or to set the number

of hours you wish the heater to operate before it automatically turns off, from 000 to 048 hours.

The icon will ﬂ ash red for a few seconds and then stays red. The heating system will operate

for the amount of preset hours only. The timer takes priority over temperature, so the heater

will shut off when HDT time runs out regardless if the preset spa water temperature is reached

or not. During the HDT function, the information shown on the LED display alternates between

the remaining heater operating hours and the water temperature. Repeat previous steps to

reprogram this function. To deactivate the function at any time, simply set the HDT time back to

000. To readjust the preset hours, press the HDT button twice and adjust the hours with and

buttons.

Example 2: Using the same scenario as example 1 above but rather than manually turning the

heater off when you are ﬁ nished, you would like the heater to turn off automatically on Saturday

evening at 9:00pm. After going through the steps in example 1, press the HDT button and then

the or button to select 048 hours. The heater will then run from Thursday at 9:00pm to

Saturday at 9:00pm.

NOTE: If HST and HDT timers are both set, the LED display will ﬁ rst alternate between

remaining time before the heater start and the water temperature, until HST timer runs out and

the heater activates. Then the LED display alternates between remaining HDT time and water

temperature until the HDT timer runs out as well.

Celsius/Fahrenheit Toggle button: The temperature can be displayed in either Fahrenheit or

Celsius. The system’s default is Celsius.

NOTE: The default temperature is 20°C (68°F). Temperature adjustment ranges from 10°C

(50°F) to 40°C (104°F).

NOTE: The spa control panel is resistant to water, but it is not designed to be completely

submerged. Do not put the control panel in the water. Submersion could cause water to enter

the panel causing damage to the electronics.

Adjustment Buttons: Press the increase or decrease buttons to adjust the desire function

settings. Press and hold the button will rapidly increase or decrease the numbers.

LED Display: Once plugged in the LED displays the current water temperature automatically.

If the control panel (3) is not placed on the control base recessed channel, the LED display will

go blank after 5 minutes. Press any button to resume the control panel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex PureSpa - 28492 PS-BH-20 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Intex PureSpa - 28492 PS-BH-20

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info