Bedienungsanleitung Inventor P9VO32 Passion Eco (Seite 13 von 156) (Deutsch, Englisch)

771590

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

 Page 12 

Refer to the following diagram to ensure proper distance from walls and ceiling:

Step 2: Attach mounting plate to wall

The mounting plate is the device on which you

will mount the indoor unit.

Remove the screw that attaches the mounting

plate to the back of the indoor unit.

Place the mounting plate against the wall

in a location that meets the standards in

the Select Installation Location step. (See

Mounting Plate Dimensions for detailed

information on mounting plate sizes.)

Drill holes for mounting screws in places that:

• have studs and can support the weight of

the unit

• correspond to screw holes in the mounting

plate

Secure the mounting plate to the wall with

the screws provided.

Make sure that mounting plate is flat against

the wall.

NOTE FOR CONCRETE OR BRICK WALLS:

If the wall is made of brick, concrete, or similar

material, drill 5mm-diameter (0.2in-diameter)

holes in the wall and insert the sleeve anchors

provided. Then secure the mounting plate to

the wall by tightening the screws directly into

the clip anchors.

Step 3: Drill wall hole for connective piping

You must drill a hole in the wall for refrigerant

piping, the drainage pipe, and the signal cable

that will connect the indoor and outdoor units.

Fig. 3.1-b

12cm (4.75in)

or more

2.3m (90.55in) or more

12cm (4.75in)

or more

15cm (5.9in) or more

Determine the location of the wall hole based

on the position of the mounting plate. Refer

to Mounting Plate Dimensions on the

next page to help you determine the optimal

position. The wall hole should have a 65mm

(2.5in) diameter at least, and at a slightly

lower angle to facilitate drainage.

CAUTION

When drilling the wall hole, make sure to

avoid wires, plumbing, and other sensitive

components.

Using a 65mm (2.5in) or 90mm(3.54in)

(depending on models )core drill, drill a

hole in the wall. Make sure that the hole

is drilled at

a slight downward angle, so

that the outdoor end of the hole is lower

than the indoor end by about 5mm to 7mm

(0.2-0.275in). This will ensure proper water

drainage. (See Fig. 3.2)

Place the protective wall cuff in the hole. This

protects the edges of the hole and will help

seal it when you finish the installation process.

 Page 13 

Wall

Indoor Outdoor

mm7-5

(0.2-0.275in)

Fig.3.2

MOUNTING PLATE DIMENSIONS

Different models have different mounting plates.

In order to ensure that you have ample room to

mount the indoor unit, the diagrams to the right

show different types of mounting plates along

with the following dimensions:

•

Width of mounting plate

•

Height of mounting plate

•

Width of indoor unit relative to plate

•

Height of indoor unit relative to plate

•

Recommended position of wall hole (both

to the left and right of mounting plate)

•

Relative distances between screw holes

Fig. 3.2

Model B

Model D

302mm(11.9in)

805mm(31.7in)

1106mm(43.5in)

599mm(23.6in)

342mm(13.5in)

Model C

964mm(37.9in)

482mm(19in)

325mm(12.8in)

406.4mm(16in)

452.7mm(17.8in)

249mm(9.8in)

153mm(6in)102mm(4in)

39mm(1.5in)

pipe hole

φ65mm

（2.56 in）

pipe hole

φ65mm

（2.56 in）

pipe hole

φ65mm

（2.56 in）

pipe hole

φ65mm

（2.56 in）

pipe hole

φ65mm

（2.56 in）

pipe hole

φ65mm

（2.56 in）

Indoor unit outline

54mm(2.1in)

Model A

717mm(28.2in)

302mm(11.9in)

318mm(12.5in)

409mm(16.1in)

249mm(9.8in)

153mm(6in)102mm(4in)

39mm(1.5in)

pipe hole

φ65mm

（2.56 in）

pipe hole

φ65mm

（2.56 in）

Indoor unit outline

54mm(2.1in)

71mm(2.80in)

132mm

(5.20in)

219mm(8.62in)

262mm(10.31in)439mm(17.28in)

Indoor unit outline

174mm

(6.85in)

320mm(12.60in)

130mm

(5.12in)

55mm(2.17in)

558mm(21.97in)

Correct orientation of Mounting Plate

NOTE: When the gas side connective pipe is

16mm(5/8in) or more, the wall hole should

be 90mm(3.54in).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Inventor P9VO32 Passion Eco Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Inventor P9VO32 Passion Eco

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info