Bedienungsanleitung Inventor V5MFI32-60 (Seite 26 von 136) (Englisch)

771744

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

 Page 26 

Outdoor Unit Installation

Outdoor Unit Installation Instructions

Step 1: Select installation location.

The outdoor unit should be installed in the

location that meets the following requirements:

o Place the outdoor unit as close to the indoor

unit as possible.

o Ensure that there is enough room for

installation and maintenance.

o The air inlet and outlet must not be

obstructed or exposed to strong wind.

o Ensure the location of the unit will not be

subject to snowdrifts, accumulation of leaves

or other seasonal debris. If possible, provide

an awning for the unit. Ensure the awning

does not obstruct airow.

o The installation area must be dry and well

ventilated.

o There must be enough room to install the

connecting pipes and cables and to access

them for maintenance.

o The area must be free of combustible gases

and chemicals.

o The pipe length between the outdoor and

indoor unit may not exceed the maximum

allowable pipe length.

o If possible, DO NOT install the unit where it

is exposed to direct sunlight.

o If possible, make sure the unit is located far

away from your neighbors’ property so that

the noise from the unit will not disturb them.

o If the location is exposed to strong winds (for

example: near a seaside), the unit must be

placed against the wall to shelter it from the

wind. If necessary, use an awning.

(See Fig. 9.1 & 9.2)

o Install the indoor and outdoor units, cables

and wires at least 1 meter from televisions or

radios to prevent static or image distortion.

Depending on the radio waves, a 1 meter

distance may not be enough to eliminate all

interference.

Strong wind

Fig. 9.1

Fig. 9.2

Step 2: Install outdoor unit.

Fix the outdoor unit with anchor bolts (M10)

>60cm / 23.6”

Fix with bolts

• Be sure to remove any obstacles

that may block air circulation.

• Make sure you refer to Length

Specications to ensure there is

enough room for installation and

maintenance.

Fig. 9.3

√

CAUTION

 Page 27 

NOTE:

The minimum distance between the

outdoor unit and walls described in the

installation guide does not apply to airtight

rooms. Be sure to keep the unit unobstructed

in at least two of the three directions (M, N, P)

(See Fig. 9.5)

Fig. 9.5

Outdoor Unit Mounting Dimensions

Rows of series installation

L ≤ H L ≤ 1/2H

L A

25 cm / 9.8” or more

1/2H < L ≤ H

30 cm / 11.8” or more

L > H Can not be installed

The relations between H, A and L

are as follows.

The mounting dimensions vary among different outdoor units.

The fixing bolt head diameter should be more than 12mm.

Outdoor Unit Dimentsion (mm) Mounting Dimentsion (mm)

W H DAB

952 1333 415 634 404

900 1170 350 590 378

Fig. 9.3

30 cm / 12” from back wall

60 cm / 24” above

30 cm / 12” on left

30 cm / 12”on right

200 cm / 79” in front

Outdoor Unit Dimentsion (mm) Mounting Dimentsion (mm)

W H DAB

681 434 285 460 292

700 550 275 450 260

300

333

363

420

555

554

702

810

770

800

845

946

487

514

540

673

298

340

350

403

Fig. 9.4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Inventor V5MFI32-60 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Inventor V5MFI32-60

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info