Bedienungsanleitung Inventum VKI 3010 ZWA (Seite 18 von 40) (Deutsch, Englisch, Holländisch, Französisch)

694976

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

installation instructions

problems & solutions

• Safety during use is only guaranteed if the assembly has taken place in a technically correct way and in accordance with this

installation instruction. The installer is liable for damage caused by an incorrect assembly.

• The cooker falls under protective class I and may only be used in combination with an earthed connection. The manufacturer

is not liable for unsuitable operation and possible damage caused by unsuitable electric installations.

• The cooker must be connected to a permanent installation in which provisions for switching off are integrated, in accordance

with the installation instructions.

• Make sure that the power supply cable does not get jammed during installation or is running along sharp edges. If an oven is

installed below it, make sure the cable runs via the rear corners of the oven to the connection box. It must be placed in such a

way that no contact is made with hot parts of the cooker or oven.

• The connection point, socket and/or plug must always be accessible.

• The worktop on which the cooker is placed must be ﬂat, horizontal and stable. Observe the instructions from the manufacturer

of the worktop.

• In case of incorrect installation or connection, the warranty becomes invalid.

• Attention: any change within the appliance, including replacement of the power supply cable, must be performed by an

authorised installer.

• Sufﬁcient space around the cooker is required for safe use. Check that this space is available.

• The distance from the cooker to an extraction hood should be at least 650 mm.

ELECTRICAL CONNECTION

Caution: this cooker is always supplied with a cord and plug. The connection is a 1 phase connection.

• Check that the voltage corresponds with what is stated on the information plate.

• Connect the cooker to an earthed socket.

• Caution: The connection point should always be within reach.

Problems Checkpoints and solutions

After inserting the plug in the socket and switching

on the induction cooker with the [ ON/STANDBY ]

key, the [ ON/STANDBY ]

indicator on the display does not light up.

• Is the plug properly inserted in the socket?

• Has the socket, fuse or cord been damaged?

The induction cooker makes a lot of noise.

The electronics of the induction cooker require cooling. It is normal for

the fan to make noise.

Error message

E0 No pan or no suitable pan has been placed.

E1 Temperature sensor defective. Contact customer service.

E2 Operating panel defective. Contact customer service.

E3 Voltage too high. Have your connection checked by an electrician.

E4 Voltage too low. Have your connection checked by an electrician.

The operating panel is overheated. Switch off the cooker and wait until

it is cooled down.

The cooker is overheated and switched off automatically. Check the

ventilation openings and allow the cooker to cool down. The induction

cooker will function normally again.

18 • English

VKI3010ZWA-instructions.indd 18 13-9-2018 09:25:05

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Inventum VKI 3010 ZWA Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info