Bedienungsanleitung Inventum VWM9001 (Seite 50 von 116) (Deutsch, Englisch, Holländisch, Französisch)

790020

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

6troubleshooting

The washing machine will automatically control the operation of particular functions during the washing cycle. If any

irregularity occurs, this will be identiﬁed by a message (E:XX) on the display. The appliance will report the error until it is

switched off. Externaldisturbances (e.g. the power grid) may result in various error reports. In such case:

• Switch off the appliance and wait for a few seconds.

• Switch the appliance on and repeat the washing programme.

• Most errors during operation can be solved by the user.

• If the error persists, call the customer care service.

• Repairs may only be carried out by an adequately trained person.

• Repairs or warranty claims resulting from incorrect connection or use of the appliance shall not be covered by the

warranty. Insuchcases, the costs of repair shall be charged to the user.

• The warranty does not cover the errors or failures resulting from external disturbances (lighting strike, power grid failures,

naturaldisasters etc.).

TROUBLESHOOTING AND ERROR TABLE

Problem/

error

Indication on the display unit

and problem description What to do?

Incorrect settings

Restart the programme. If the error reoccurs, call a service technician.

Temperature sensor error Inlet water too cold. Repeat the washing programme. If the washing

machine reports this error again, call a service technician.

Door lock error

Make sure the washing machine door is closed. Unplug the power cord

from the outlet; then, plug the power cord back into the outlet and switch

on the washing machine. If the error reoccurs, call a service technician.

Water ﬁlling error

Check the following:

• is the water inlet valve open,

• is the ﬁlter on the water supply hose clean,

• is the water supply hose deformed (clipped, clogged etc.),

• is the pressure in the water mains between 0.05 and 0.8 MPa (0.5–8 bar).

Then, press the Start/Pause button to resume the programme. If the

error reoccurs, call a service technician.

Motor error

Restart the programme. If the error reoccurs, call a service technician.

Motor error

Restart the programme. If the error reoccurs, call a service technician.

Water heating error

Restart the programme. If the error reoccurs, call a service technician.

Water draining error

Check the following:

• is the pump ﬁlter clean,

• is the discharge hose clogged,

• is the drain clogged,

• if the discharge hose placed is placed below the maximum and above

the minimum height (see chapter »INSTALLATION AND CONNECTION/

Connecting and securing the water discharge hose«); then, press the

Start/Pause button again. If the error reoccurs, call a service technician.

50 • English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Inventum VWM9001 Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info