Bedienungsanleitung Inverto IDL-5000HD (Seite 17 von 66) (Englisch)

509835

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

1EnIDL5000HD-print.fh10 1/18/06 12:53 PM Page 17

Composite

C M Y CM MY CY CMY K

6.6.3.8 Motor Settings

If you wish to connect the receiver to a rotating antenna (DiSEqC Level 1.2), call up the Main Menu, then

pressing Installation / Setup, then pressing “ Outdoor Settings”, then go to entry “ LNB Type” and use the

/ directional keys to select the setting “Motorized” for every LNB number, which has to be controlled by

the motor. Where you will find a facility for setting the position of the antenna manually for the various

satellite positions, and can then store these positions in memory. In the window “ Motor settings”, select

from the displayed list the satellite you want to reach with the next antenna position. The receiver at this

stage has already registered which transponders are available on this satellite, and will indicate the signal

strength and quality in the form of a bar graph. You can use this to find the optimum for the antenna.

In order to rotate the antenna towards the East or West, use the directional keys to select either “Move

coarse” or “More fine”. When the satellite position has been found, select “Save Position” in order to store

this permanently. In future, the receiver will automatically turn the antenna to this position whenever you

tune to a programmed slot available from this position.

Apart from storing all required satellite positions, you should also make a point of programming an easterly

and a westerly limit position for the motor. This is particularly important if other buildings or structures in

the vicinity restrict the rotation of the antenna. These could damage the antenna, motor or surrounding

objects if pre-programming does not restrict the limit of rotation.

6.6.4 Channel Search

New digital satellite TV and radio program are added almost on a

day daily basis, or existing program will change their frequency.

If you wish to receive these programs, you must allocate them to

specific program slots in the program list, and store them in memory.

The program search function is designed to assist you in this

activity, and there are various types of program search available.

Several procedures can be followed in order to initiate a program

search. Press the “Menu” key to call up the Main Menu, then using

the / directional keys select the sub-menu “Installation / Setup”,

followed by “Channel Search”, confirming your selection in each

case by pressing the “OK” key. Here you can decide between the

three options.

6.6.4.1 Quick Search

Use the automatic program search to allow your receiver to search

through an entire satellite position for new program. In this case,

the entire frequency range of the satellite is searched. The following

information must be input to the receiver:

Satellite: First select the satellite position to be searched. Below

this you will see a display of the current signal strength.

All newly found program would now be displayed on the following

page. At the end, the result of the program search will be displayed.

The search procedure can be terminated at any time by pressing

the “EXIT” key.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Inverto IDL-5000HD Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info