Bedienungsanleitung Inverto IDL-5000HD (Seite 18 von 66) (Englisch)

509835

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

1EnIDL5000HD-print.fh10 1/18/06 12:53 PM Page 18

Composite

C M Y CM MY CY CMY K

6.6.4.2 Advanced Search

In addition to the automatic search, a manual search procedure

is also available. In this case you must search specifically for the

program on a specific satellite transponder. Unlike the automatic

search procedure, here you must enter all reception parameters

explicitly.

The technical reception parameters that must be entered in this

display can be obtained either from satellite magazines, or from

the relevant program provider.

The following information must be input:

Satellite: First select the satellite position to be searched. Below this you will see a display of the current

signal strength.

Frequency: Here you must enter the five-digit transponder frequency, e.g. 11836 for 11.836GHz.

Polarity: Here you must enter the polarization plane of the transponder (“Horizontal” or “Vertical”).

Symbol rate: Either select one of the two usual rates commonly found on the Astra and Eutelsat satellites,

22.000 as well as 27.500 symbols/s, or enter a specific value manually. The receiver is equipped to process

symbol rates between 2.000 and 45.000 symbols/s.

Scan Filter: There are three choices:

FTA: Only search free-to-air programs.

FTA+Irdeto: Search free-to-air plus Irdeto scrambled programs

All: Search all kinds of programs, including other CA systems.

PID Video: Packet identifier for the video signal

PID Audio: Packet identifier for the audio signal

PID PCR: Program Clock Reference

Now press the red function key to initiate the manual program search. All program broadcasting within the

framework of specified parameters will be displayed, one after the other, on the following page. You can

then decide whether you want to store the newly found program in memory, or whether you wish to discard

them. The search procedure can be terminated at any time by pressing the “EXIT” key.

6.6.4.3 Preprogrammed List

The receiver automatically selects your country name. The sub-

display “ Do you want to reinitialise the program list? “, Please

pressing the “ OK” key, then will be initialising the program. Please

wait about 15 seconds.

6.6.5 Time / Date Settings

Time/Date settings: If the ”Automatic Time Update” is set to “On”,

the receive will receive the digital clock time and date as broadcast

by the digital TV programmed providers. The DVB standard will

broadcast this in GMT time zone. In order to display local time

correctly, It may be necessary to set a time offset, indicating the

difference between local time and GMT (e.g. in Germany daylight

savings time in summer is +2h, winter time is +1h)

Clock mode: The time can be displayed in 12 or 24-hour format.

Automatic Time Update: The receiver can either receive the

Current time via the digital TV programmers (On),

Or it can calculate current time independently (Off).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Inverto IDL-5000HD Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info