Bedienungsanleitung Inverto IDLV-5000P (Seite 8 von 16) (Englisch)

509864

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

5.1 INPUTS MENU

There are four options: Status, DVB-S2, RSSI and Ethernet (optional):

5.1.1 Status Menu

It contains four options, ASI1, ASI2, TUNER and IP IN, to show the status of signal input:

ASI1:

• When signal from ASI1 input port is locked, it will display package format and code rate; if signal is

not locked, it will show Unlock.

ASI2:• When signal from ASI2 input port is locked, it will display package format and code rate; if signal is

not locked, it will show Unlock.

TUNER:• When signal from tuner input port is locked, it will display package format and code rate; if signal

is not locked, it will show Unlock.

IP IN: • When signal from IP input port is locked, it will display package format and code rate; if signal is not

locked, it will show Unlock.

Note: this option only appears when set the External Function as “IP IN”. Please refer to section ‘Optional

Function’ for setting method.

5.1.2 DVB-S2 Menu

There are 6 options to set DVB-S2 parameters. After signal is locked, the TUNER LOCK indicator on front panel

will turn green.

LNB Frequency:

• Input LNB frequency

Satellite Frequency:• Input downstream frequency of satellite

Symbol Rate:• Input symbol rate of satellite

LNB Voltage:• select the correct LNB voltage output of the F-connector: Off, 13 V, 18 V. <A>

LNB 22KHz: • activate the LNB 22 kHz control signal to the LNB: On or Off. <B>

DISQEC: • Can select OFF/Port A/Port B/Port C/Port D

Note: please contact the local satellite operator for the satellite frequency and symbol rate.

<A> Normally, 13V switches the LNB to receive Vertical/Left hand polarization while 18V receive Horizontal/Right

hand.

<B> Normally, 22KHz control signal switches the LNB to receive high band if any.

5.1.3 RSSI

There are two options to show the quality of receiving DVB-S2 signal.

5.1.4 Ethernet Menu

Note: The Ethernet menu is showed only if the IP streaming in/out board is installed and the TS/IP streaming

board is set to “IP IN”. Refer to section ‘Optional Function’.

The Ethernet connector is for receiving transport stream over IP. The Ethernet connector has user-congurable

IP address, network mask and default gateway. These must be set to appropriate values for the network over

which the transport stream over IP is received.

Stream IP Addr:

• Enter the IP address for streaming IP input of the unit.

Stream Netmask:• Enter the network sub mask for the subnet to which the unit is connected for IP

streaming trafc.

Stream Gateway:• Set the gateway for the network to which the unit is connected for IP streaming trafc.

Stream Mac Address:• factory-set MAC addresses are guaranteed to be unique. Therefore you cannot

congure the address.

Inputs

Status

DVB-S2

RSSI

Ethernet

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Inverto IDLV-5000P Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info